Name: 2w wireless rs485 transceiver rs232 radio modem long range data communications sma 433mhz antenna receiver 450mhz 470mhz
Brand: thingsend
Availability: InStock

Product Details

Specifications:

1 Features:

l Max. 2W Lower Power Emission

l High receiving sensitivity up to -123dBm/1200bps

l 3km-5km line of sight long transmission distance

l About 80g light weight

l With RS232&RS485 2 interface, TTL customized

l 0-16 Channels(DIP switch select and PC programming)

2 Pin Definitions

Pins	Definition	Description	Level	Terminal Connection
1	VCC	DC 5V	Positive power supply 8-36V can be set in factory
2	Rxd/RS232	Data Input	RS232 Level	Txd/RS232
3	Txd/RS232	Data Output	RS232 Level	Rxd/RS232
4	GND	Ground of power supply	Negative power supply
5	SGND	Signal	SGND	Signal
6	A/RS485	RS485 Signal+	RS485 Level	A/RS485
7	B/RS485	RS485 Signal-	RS485 Level	B/RS485
8	NC	NC
9	NC	NC

3 Working Frequency

The DIP switch can select 0~16 channels, and frequency point of 1~15 channels is fixed, and the frequency of the 0 channel can be set and saved arbitrarily through our software. Dial switch to "ON", means "1", dial "OFF" means "0", "1 is high" and "4" is "low.

Channel (1234)	Frequency(MHz)	Channel (1234)	Frequency(MHz)
0(0000)	453.25000	8(1000)	449.75000
1(0001)	425.25000	9(1001)	456.75000
2(0010)	428.75000	10(1010)	460.25000
3(0011)	432.25000	11(1011)	463.75000
4(0100)	435.75000	12(1100)	467.25000
5(0101)	439.25000	13(1101)	470.75000
6(0110)	442.75000	14(1110)	474.25000
7(0111)	446.25000	15(1111)	477.75000

4 Software Function Setting

4.1 Enter setup mode

Continues to send 3 + numbers at current baud rate, XZ-DT254 enters setup mode, and the serial port outputs OK at this time

Format + + +

Return OK

4.2 Set Channel 0 Frequency

Format >WF0/RX:453.25000/TX: 453.25000

Return

Explain >WF0 means working frequency when writing channel 0

RX: means receiving frequency453.25000 MHz ,please notice frequency needs to be accurate to 5 digits after the decimal point；

TX: means transmitting frequency 453.25000 MHz , please notice frequency needs to be accurate to 5 digits after the decimal point；

XZ-DT254 receiving and transmitting frequency range：420 ~ 480MHz, the same XZ-DT254 receiving and transmitting frequency settings can be the same or different, but modules in the same communication system must have the same receiving and transmitting frequency then they can communicate.

4.3 Baud Rate Setting

Format >WBA

Return

Explain >WB means interface baud rate

A~E means 1200~19200bps；A=1200、B=2400、C=4800、D=9600、E=19200 4.4 Parity Bits Setting

Format >WVN

Return

Explain >WV means Interface Parity Bit

N、E、O means 8N1、8E1、8O1

4.5 Emission Power Level Setting

Format >WP3

Return

Explain > WP means writing power level

1、2、3 means 0.5W、1W、2W

4.6 Read all Parameters Command

Format >WP3

Return

Explain Output XZ-DT254 current working parameters

4.7 Exit Setup Mode

Format >WE

Return OK

XZ-DT254 exit setup mode，even if XZ-DT254 enter setup mode it will exit when it does not have any command actions at continuous 10S.

5 Technical Parameters:

Frequency Range	420～480MHz
Frequency stability	≤±2.5PPm
Transmit Power	2W(33dBm)
Modulation	GFSK
RF Data Rate	1200～19200bps
Interface	RS232&RS485(TTL customized)
Power Supply	5V@2A(8～36V customized in factory)
Interface Data Format	8E1/8N1/801
Transmission Distance	3km-5km line of sight (if Antenna is put at above 2m height)
Receiving Sensitivity	-123dBm@1200bps/-118dBm@9600bps
Channel Bandwidth	10KHZ@1200bps/25KHZ@9600bps
Working Temperature	-40℃～80℃ (industrial grade)
Working Humidity	10% to 90% relative humidity, no condensation
Emission Current	≤1500mA
Receiving Current	≤50mA
Dimension(L/W/H)	86 X 45 X 20 mm
Weight(g)	≤80g

OEM wireless solutions are supportable.Welcome to contact me Sarah if have any queastions. sales(at)thingsend(dot)com