Lithium Aluminum Alloy Product Manual[/b]

[/b]

Part One [/b]

Basic Information of Product[/b][/b]

English NameLITHIUM ALUMINUM ALLOY POWDER

UseAnode of Primary Lithium Battery

Chemical Composition20±1% Lithium, Remainder aluminum

AppearanceSilvery-white Powder

Specification40 mesh 60mesh 80mesh

100mesh 200mesh

Package Sealed in grinding bottle with Argon gas and then put into iron can which is filled with foam and shipped in wooden box.

Package Specification125mL grinding bottle 250mL grinding bottle

[b]Part Two [/b]

[b]Manufacturer Information[/b][b][/b]

Company Name[/b][/b]China Energy Lithium Co., Ltd.

Address[/b][/b]No.9 Factory, the Third Factory District, No. 59, 4th Avenue, TEDA, Tianjin,China [/b]

Tel[/b][/b] 02259816836[/b]

Post Code[/b][/b]300457[/b]

[/b]

Mailing address[/b][/b]Sales Department[/b]

Company Name[/b][/b]China Energy Lithium Co., Ltd.

Sales Address[/b][/b]Building A2, Tian Da Science& Tech Zone, 4th Avenue TEDA, Tianjin City , China [/b]

Tel: 02259816836[/b]

02259816832[/b]

Fa[/b]x: [/b] 02259816836[/b]

[/b]

[b]Part Three [/b]

[b]Product Property[/b]

1Lithium aluminum alloy powder can react with atmospheric moisture, oxygen, nitrogen and carbon dioxide of the air. It can self-ignite in humid air. The main production after burning in the air is Lithia and alumina. Lithia can form lithium hydroxide after absorbing water.

2React violently with water and form hydrogen which can burn and explode under some certain conditions and lithium hydroxide.

3React violently when contacting acid and halogen.

4The product burns easily and explodes when comes into contact with ignition source or impact during the course of shipping and using.

[/b]

Part Four [/b]

Using Method[/b]

1Check if the package is intact, the label is clear and the packing list, product certificate and manual are complete before using.

2Check if the usage date is within product validity date.

3Check if the product has absorbed moisture or oxidation has occurred. If the package or product has expanded, split, become hot, become black and lumpy, the product cant be used any more and need to be discarded as waste.

4The product should be opened in the glove box with an argon atmosphere or in a drying room where the relative humidity is lower than 3%.

5Safety precautions should be taken before opening the product and workers should wear safe work clothes, respirator, hat, glasses and gloves.

6Taking out the product from iron can and opening glass bottle should be performed on the operating table in case explosion occurs if dropped accidentally.

7Cut the adhesive tape around the bottle before opening it and then push off the lid of the bottle carefully. Any strong unscrewing of the lid is forbidden in case the friction causes burning and explosion.

8Try to use all the product after opening the package. Product that cant be used up should be put into a bottle which is sealed with paraffin and kept carefully until discarded as waste.

9Only open one bottle of product at a time to avoid danger.

10The operator who has water or sweat on the hands, body, or skin or has any wounds is not allowed to contact lithium aluminum powder.

11The operators should keep a certain distance from each other to reduce any injury that may occur when there is an accident.

Part Five [/b]

Description of Product Dangers [/b]

1The danger mainly comes from the high temperature of self-burning, stimulating fog and the harm of explosion of hydrogen which is produced when product meets water.

2Lithium hydroxide is produced when the product meets moisture on the skin, sweat, blood and the moisture around eyes and respiratory path. This will cause pain and harm to the body.

Part Six [/b]

Preventive Measure[/b][/b]

1Respiratory: Suggest wearing absorbent cotton dust mask or multilayer gauze respirator with absorbent cotton inner layer.

2Hand: Dry rubber gloves or surgical gloves for general use.

3Eyes: Suggest wearing eye shield

4Environmental measure: Product should be opened in the dry room where the relative humidity is lower than 3% or in an argon atmosphere glove box.

5Others: Asbestos quilt, gloves, shovel and dry sands should be prepared in the working area.

Part Seven [/b]

First Aid Measures[/b]

1If you come into contact with the product, quickly wipe off as much as possible with a dry cloth then immediately flush with plenty of water for at least 5 minutes. Thoroughly wash with soap and water. Try to avoid skin damage from lithium hydroxide reacting with moisture and sweat on the surface of the skin.

2Skin: If product has reacted with moisture and sweat on the surface of skin and causes an itching and burning feeling, daub with edible vinegar or boric acid of 2%, then flush with water.

3Eye contact: Immediately flush with water for at least 10 minutes, See medical doctor or ophthalmologist immediately.