It covers almost all Opel cars, even new cars with CAN-BUS based
diagnostic, such as Vectra-C, Astra-H, Zafira-B.
The program lets you to read out and clear fault codes, shows you live data,
lets you to perform output test, and supports remote, and key programming.
The program supports many control units, like Engine, Automatic
Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster,
Electronic Climate Control, Body Control Unit, just to name a few examples.
Since Opel uses many pin in the OBD connector, the diagnostic interface
works as a multiplexer, and selects the appropriate pin for communication.
PIN3, PIN7, PIN8, PIN12 = Serial Link (ISO9141, KW81, KW82, KWP2000) Fault
codes will be shown with all available information:
Full fault code text description Full status information (Present, Not present,
Intermittent)
You can print out, save, or copy the fault codes to any other application.
From the fault codes window, you can go directly to the measuring blocks
window.
The program shows you measuring block information on many control
module, you can choose anything from the list on your own. The program is
capable of showing 8 measuring block parameter simultaneously. The
sample rate is depends mostly on the communication protocol. For example,
older system, like Omega-B X 25 DT Engine (ISO-9141-2) can be very slow,
during communication, while newer Multec, or Bosch units are faster (using
KWP-2000), and the newest CAN based control units are very fast!
You can also run output tests on many controllers.
PIN6-PIN14
PIN3-PIN11
PIN1
HSCAN - Dual-wire, High Speed CAN-BUS, 500 kbps
MSCAN - Dual-wire, Medium Speed CAN-BUS, 95 kbps
SWCAN - Single-wire, Low Speed CAN-BUS, 33.3 kbps
You will get a feedback on the state of the activated output. This will helps
you to find the failed components more easily.
With OP-COM, you can learn keys to immobiliser, and remote keys to the
central door locking, or alarm.
You can also reset, and program the following immobiliser related items:
ECM, BCM, IPC.
You will need the vehicle security code, which can be found on the CAR-
PASS.
You can also reset, and program the Service interval reminder on Astra-G,
Zafira, Corsa-C, Meriva, Tigra-B
You can code SAB6, and SAB8 airbags with the software.
The diagnostic inteface is USB port based, so there will be NO
COMPATIBILITY ISSUES, with serial to USB converters.
The speed of the communication over the USB-BUS is enough to handle the
awesome speed of the High-Speed CAN-BUS systems, which is currently
500kbps. This is the main reason, why only the USB port based interface is
available for CAN-BUS.
Compared to the TECH2, which is the dealers tool (with a 32 MB card+CANdi
interface), the price of OP-COM is quite affordable. Not to mention the free
software updates, which can be downloaded from the internet.
OP-COM is currently available at the following languages:
Hungarian (a widespread, and beautiful language too :) )
English
German
Turkish
Romanian
French
Danish
Portuguese
Slovakian
IMPORTANT: The program can only be used with a special interface
hardware.
A simple serial or USB port based standard interfaces (K, KKL, etc) cannot
be used!
diagnostic, such as Vectra-C, Astra-H, Zafira-B.
The program lets you to read out and clear fault codes, shows you live data,
lets you to perform output test, and supports remote, and key programming.
The program supports many control units, like Engine, Automatic
Transmission, ABS, Airbag, Engine Cooling module, Instrument Cluster,
Electronic Climate Control, Body Control Unit, just to name a few examples.
Since Opel uses many pin in the OBD connector, the diagnostic interface
works as a multiplexer, and selects the appropriate pin for communication.
PIN3, PIN7, PIN8, PIN12 = Serial Link (ISO9141, KW81, KW82, KWP2000) Fault
codes will be shown with all available information:
Full fault code text description Full status information (Present, Not present,
Intermittent)
You can print out, save, or copy the fault codes to any other application.
From the fault codes window, you can go directly to the measuring blocks
window.
The program shows you measuring block information on many control
module, you can choose anything from the list on your own. The program is
capable of showing 8 measuring block parameter simultaneously. The
sample rate is depends mostly on the communication protocol. For example,
older system, like Omega-B X 25 DT Engine (ISO-9141-2) can be very slow,
during communication, while newer Multec, or Bosch units are faster (using
KWP-2000), and the newest CAN based control units are very fast!
You can also run output tests on many controllers.
PIN6-PIN14
PIN3-PIN11
PIN1
HSCAN - Dual-wire, High Speed CAN-BUS, 500 kbps
MSCAN - Dual-wire, Medium Speed CAN-BUS, 95 kbps
SWCAN - Single-wire, Low Speed CAN-BUS, 33.3 kbps
You will get a feedback on the state of the activated output. This will helps
you to find the failed components more easily.
With OP-COM, you can learn keys to immobiliser, and remote keys to the
central door locking, or alarm.
You can also reset, and program the following immobiliser related items:
ECM, BCM, IPC.
You will need the vehicle security code, which can be found on the CAR-
PASS.
You can also reset, and program the Service interval reminder on Astra-G,
Zafira, Corsa-C, Meriva, Tigra-B
You can code SAB6, and SAB8 airbags with the software.
The diagnostic inteface is USB port based, so there will be NO
COMPATIBILITY ISSUES, with serial to USB converters.
The speed of the communication over the USB-BUS is enough to handle the
awesome speed of the High-Speed CAN-BUS systems, which is currently
500kbps. This is the main reason, why only the USB port based interface is
available for CAN-BUS.
Compared to the TECH2, which is the dealers tool (with a 32 MB card+CANdi
interface), the price of OP-COM is quite affordable. Not to mention the free
software updates, which can be downloaded from the internet.
OP-COM is currently available at the following languages:
Hungarian (a widespread, and beautiful language too :) )
English
German
Turkish
Romanian
French
Danish
Portuguese
Slovakian
IMPORTANT: The program can only be used with a special interface
hardware.
A simple serial or USB port based standard interfaces (K, KKL, etc) cannot
be used!
