CDMA 850mhz Mobile Phone signal boosterA signal booster or cell phone repeater is a device used for boosting the cell phone network to the local area by the usage of a reception antenna. In simple words,Website: , wireless signal booster is a device to boost the wireless signal and this device make wireless coverage more and more. Wireless repeaters are practical, beautiful and easy to install.Wireless repeaters are designed to meet the needs and requirements of modern citizens. Wireless repeaters come complete with everything necessary for a full cell phone repeater system enabling you to use your cell phone wherever you are. One of the most popular applications of a wireless signal repeater is its use in buildings which are signal isolated. When a house is located too far from the telecom station, which is usually installed around a city, cell phone signal can be very low.We provides signal boosters kits for any Homes, Offices, Cars, RV\'s, Boats and more. All amplifier kits come with Indoor and Outdoor Antennas, Cables, Power adapters and more.HPC-C27 LTE 850mhz repeater Features:1.With unique appearance design, have good cooling function2.With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;3.With DL signal LED display, help to install the outdoor antenna at the best state;  4.With AGC and ALC, make repeater work stable . 5.PCB with isolation function ,make UL and DL signal not influence each other,6.Low intermodulation, high Gain ,stable Output power HPC-C27 LTE850 repeater Inside and Outside DesignHPC-C-27  Dual band repeater is to support any two mobile band existing in the world to help end users to improve mobile signals for much better phone call quality and smoother data transmission. It is designed to support coverage area max can up to 2000 square meters with proper engineering. Below are the main features.1.The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.2.Manual gain control (MGC) available for both uplink and downlink to adjust the gain value for proper coverage during installation or maintenance.3.To maintain safe and specific output signal levels and give alarms on self-oscillation, the repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater depending upon the strength of input signals.4.Auto shut off function available for both uplink and downlink to avoid deep self-oscilation from jamming the towers, saving your trouble from operators. 5.Wide band feature enables all devices operating within the wide frequency range of the repeater to see an improvement in performance.6.Multiple phones and other handheld devices throughout a building can benefit from a wireless repeater.7.Supports up to (500) users / calls simultaneously.8.Extended phone battery life. (Your phone does not need to put out as much power due to improved reception.)Manual Gain ControlWhat is MGC function? And what is the advantage?MGC function means Manual Gain Controlwhen your outdoor signal too stronger, so the repeater can not work well and have noise, so you can adjust the Gain by yourself ; Manual Gain Control (MGC)Code switch→Attenuation：DL：1→1dB  2→2dB  3→4dB  4→8dB  5→16dB  UL：6→1dB  7→2dB  8→4dB  9→8dB  10→16dB      Switches1-5 represents Downlink and 6-10 represent Uplink.When it is necessary to adjust the gain by the switch, firstly please adjust Downlink gain according to input signals, secondly please adjust Uplink gain according to Downlink gain. For Example you want to make the 3G Gain down 1dB, so you make the switches “1” and “6”is OK.The switches have default “OFF” status; please push relevant switches to “ON” position if certain attenuation value needs to be achieved.The Downlink attenuation settingThe Uplink attenuation settingSpecification of HPC-C-27 LTE 800mhz band repeater:Electrical specificationUplinkDownlinkFrequency RangeLTE 800824- ~ 849 MHz869 ~ 894 MHzMax .Gain≥ 70dB≥ 75dBMax .Output Power≥ 24dBm≥ 27dBmMGC ( Step Attenuation )≥ 31dB / 1dB stepAutomatic Level Control≥ 20dBGain FlatnessGSM & CDMATpy≤  6dB(P-P); DCS,PCS ≤  8dB(P-P)WCDMA≤  2dB/ 3.84MHz,Full Band ≤  5dB(P-P)Noise Figure≤  5dBVSWR≤  2.0Group Delay≤  1.5μsFrequency stability≤  0.01ppmSpurious Emission & Output inter-modulationGSM Meet  ETSI TS 151 026 V 6.1.0WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )CDMA Meet  IS95 & CDMA2000WCDMA SystemSpurious Emission MaskMeet 3GPP TS 25.143 ( V 6.2.0 )Modulation Accuracy≤  12.5%Peak Code Domain Error≤  -35dB@Spreading Factor 256CDMA SystemRhoρ > 0.980ACPRMeet IS95 & CDMA2000Mechanical  SpecificationsStandardI /O PortN-FemaleImpedance50 ohmOperating Temperature-25ºC~+55ºCEnvironment ConditionsIP40Dimensions155x112x85mmWeight≤  1.50KgPower SupplyInput AC90-264V,output DC 5V / 3ALED  AlarmStandardPower LEDPower IndicatorUL LEDBe lighted when there is phone callingDL 1Be lighted when Outdoor signal is -65dBDL 2Be lighted when Outdoor signal only -55dBDL 3Be lighted when Outdoor signal only -50dBTerms and ConditionsCertificateCE/RoHsCountry of OriginChinaPort of DispatchShenzhenProduction Capacity1000pcs/monthDate of DeliveryWithin 3 days after received payment informMOQ10pcsWarranty2yearsPacakge1pcs/box; 20pcs/cartonCountry of OriginChinaThe installtion of the RepeaterOutdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal), (Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add more antenna,the HPC-C-27 Max can work with 10pcs indoor antenna.  ( when add antenna ,please remember to take splitters )Installation steps Step 1 Start by taking your phone up to the roof or other location outside to find where the signal is strongest.Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later.Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the Signal Repeater.Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna.Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here.Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port.Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible.Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation.Of course there are still a few more things to consider but in general, this is the basic procedure. For more information, please contact us.