NXP MCU ARM Flash 32KB Integrated Circuit Parts for Industrial
USD $1$/ - $1.2$/ /Set
Min.Order:1 Set
High Performance Integrated Circuit Parts HS4-3282-8 CMOS Bus Interface Circuit
EU RoHS 16 Pin Header Terminal Block Connectors For Communication
8 Pin Terminal Block Connectors Rectangular Male Header Connector
Active PCB Terminal Block Connector Straight 8 Pos Dual STR Gold
Screw Mounting Mini GPS Active Antenna Waterproof GPS Receiver Antenna
Huawei M.2 Developer Kit Wireless Development Kit , EVB KIT Board Development Board KIT
NXP MCU ARM Flash 32KB Integrated Circuit Parts for Industrial
Description:
• System:
– ARM Cortex-M0 processor, running at frequencies of up to 50 MHz.
– ARM Cortex-M0 built-in Nested Vectored Interrupt Controller (NVIC).
– Serial Wire Debug.
– System tick timer.
• Memory:
– On-chip flash programming memory for LPC1100, LPC1100L, and LPC1100C
series: 32 kB (LPC1114/LPC11C14), 24 kB (LPC1113), 16 kB
(LPC1112/LPC11C12), or 8 kB (LPC1111), 4kB (LPC1110).
– On-chip flash programming memory for LPC1100XL series: 8 kB (LPC1111), 16 kB
(LPC1112), 24 kB (LPC1113), 32 kB (LPC1114/203/303), 48 kB (LPC1114/323),
56 kB (LPC1114/333), 64 kB (LPC1115).
– 8 kB, 4 kB, 2 kB, or 1 kB SRAM.
– In-System Programming (ISP) and In-Application Programming (IAP) via on-chip
bootloader software.
– LPC1100XL series only: page erase IAP command.
• Digital peripherals:
– Up to 42 General Purpose I/O (GPIO) pins with configurable pull-up/pull-down
resistors. Number of GPIO pins is reduced for smaller packages and
LPC11C22/C24.
– GPIO pins can be used as edge and level sensitive interrupt sources.
– High-current output driver (20 mA) on one pin.
– High-current sink drivers (20 mA) on two I2C-bus pins in Fast-mode Plus.
– Four general purpose timers/counters with a total of four capture inputs and up to
13 match outputs.
– Programmable WatchDog Timer (WDT).
• Analog peripherals:
– 10-bit ADC with input multiplexing among up to 8 pins.
• Serial interfaces:
– UART with fractional baud rate generation, internal FIFO, and RS-485 support.
– Two SPI controllers with SSP features and with FIFO and multi-protocol
capabilities (second SPI on LQFP48 packages only).
– I
2C-bus interface supporting full I2C-bus specification and Fast-mode Plus with a
data rate of 1 Mbit/s with multiple address recognition and monitor mode.
– C_CAN controller (LPC11Cxx only). On-chip CAN and CANopen drivers included.
– On-chip, high-speed CAN transceiver (parts LPC11C22/C24 only).
• Clock generation:
– 12 MHz internal RC oscillator trimmed to 1% accuracy that can optionally be used
as a system clock.
– Crystal oscillator with an operating range of 1 MHz to 25 MHz.UM10398 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2014. All rights reserved.
User manual Rev. 12.3 — 10 June 2014 7 of 547
NXP Semiconductors UM10398
Chapter 1: LPC111x/LPC11Cxx Introductory information
– Programmable watchdog oscillator with a frequency range of 7.8 kHz to 1.8 MHz.
– PLL allows CPU operation up to the maximum CPU rate without the need for a
high-frequency crystal. May be run from the system oscillator or the internal RC
oscillator.
– Clock output function with divider that can reflect the system oscillator clock, IRC
clock, CPU clock, and the Watchdog clock.
• Power control:
– Integrated PMU (Power Management Unit) to minimize power consumption during
Sleep, Deep-sleep, and Deep power-down modes.
– Power profiles residing in boot ROM allowing to optimize performance and
minimize power consumption for any given application through one simple function
call. (On LPC1100L and LPC1100XL parts only).
– Three reduced power modes: Sleep, Deep-sleep, and Deep power-down.
– Processor wake-up from Deep-sleep mode via a dedicated start logic using up to
13 of the functional pins.
– Power-On Reset (POR).
– Brownout detect with up to four separate thresholds for interrupt and forced reset.
• Unique device serial number for identification.
• Single 3.3 V power supply (1.8 V to 3.6 V).
• Available as LQFP48 package, HVQFN33 package.
• LPC1100L series also available as HVQFN24, TSSOP28 package, DIP28 package,
TSSOP20 package, and SO20 package.
• Available as dual-chip module consisting of the LPC1114 single-chip microcontroller
combined with a PCF8576D Universal LCD driver in a 100-pin LQFP package (part
LPC11D14FBD100/302).1
Specification:
Standard package |
260pcs/tray |
Category |
Integrated Circuits (ICs) |
Family |
Embedded - Microcontrollers |
Series |
LPC1100L |
Packaging |
Tray |
Core Pro |