Delivery Time:1, Sample and small order: Within 5 working days after receiving your payment. 2, Bulk order: 3 weeks after receiving deposit.
Certification:SEMKO /CE

50W Multifunction Dimmable LED Driver PUSH / 1-10V For LED Panel Light 350 – 1050mA

Description:

1, Press-in type terminal blocks for input and output side, very easy to installation.

2, DIP switch design is for different current and voltage selecting, maximum current up to 1050mA. Different LED light can chose the same model LED driver, save cost for purchasing and inventory management.

3, Dimmable LED driver with primary PUSH, secondary PUSH and 1-10V dimming interface.

4, Jumper design for switching different dimming modes, it is very convenient to select suitable dimming function as you required.

5, Memory function: The driver has built-in permanent memory against power failure. Lights can return to previous dimming level when switch off and on again, even at mains restores.

6, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the same switch. This means there is no need for any additional synchrony wire in larger installations, where many drivers should be controlled by one switch.

7, Maximum length of the cable, from switch to last driver is 20m.

8, Factory setting: 100% dimming level and 350mA output.

9, Reset the LED diver easily by a jumper.

10, Press-in terminals in primary and secondary side, easy assembly.

11, Protection: Short circuit / Over voltage / Over temperature.

12, Long life span 50,000h, 5 years guaranty.

Applications:

For LED panel light, LED down light, led strip, led tube etc…

Dimming Operation:

A) PUSH Dim

Short push (<0.1sec): Ignore, to avoid reaction on AC spike.

Short push (0.1~1sec): Switch on or switch off.

Long push (>1sec): Dimming up or down, dimming level automatically stops at minimum or maximum value.

B) 1-10V Dim

Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.

Synchronization:

For the resynchronization to work correctly when more than one driver is connected to the same push button, follow steps of below after the drivers are connected:

A) Press push button for more than one second, followed by a short push (<1s), now, led light switches off.

B) Do a long push, the system will be resynchronized.

Specifications

INPUT	Input voltage	220-240Vac
Input frequency	50-60Hz
Input current	0.26A max
Power factor	≥0.90
Efficiency(Note1)	≥87%
Leakage current	＜0.5mA/240Vac
OUTPUT	Output current/voltage and load	350mA 16-60V DC 21W max  500mA 16-60V DC 30W max 550mA 16-60V DC 33W max  650mA 16-58V DC 41W max 700mA 16-58V DC 41W max  750mA 16-56V DC 43W max 850mA 16-56V DC 47W max  900mA 16-56V DC 50W max 1050mA 16-48V DC 50W max 12Vdc 0-1050mA 12.6W max 24Vdc 0-1050mA 25.2W max
Output load range	1x50W max
Current accuracy	±5%
Dimming mode	1-10V, PUSH
ENVIRONMENT	Working temp.(Ta)	-20~50℃
Surface temp.(Tc)	85℃max
Working humidity	20~90%RH non-condensing
Storage temp.	-40~80℃
Life time	≥50000hours
PROTECTION	Isolation class	Class I, SELV
Protection class	IP20
Short circuit	Protection type; auto rest
Over voltage	Protection type; auto rest
Over temperature	Protection type; auto rest
SAFETY&EMC