Delivery Time:7-15days
Certification:ISO
Marble Glue Waterproof Tile Adhesive White For Ceramic Floor

Product Name	PB-05 Marble Tile Adhesive(C2)
Feature	Strong cohesion force, strong water retention, non-toxic, easier construction, good flexibility
Appearance	White, gray power
Application	Suited for bonding marble on interior and exterior wall and floor
Surface Preparation	Smooth and firm, no dust, grease, release agents, batik material, etc.
Dry Time	About 24h (according to the weather)
Adjust Time	about 15min
Cool Time	about 10min
Construction Temperature	5℃~40℃

PB-05 Marble Glue(C2) specially for  bonding marble on interior and exterior wall and floor. Marble is high strength, heavy, low water-absorption, back smooth and becomes yellow when meets alkali. PB-05 is high bonding strength, low alkali and avoids the marble becoming yellow. Suitable for bonding marble on cement mortar, concrete, Eterpan etc such strong substrates.
 

Product Description

Marble Adhesive:

Use:

PB-05 Marble Glue is a new kind adhesive which specially applies on sticking marble, granite, and other big stones on cement or concrete surface. PB-05 has the advantages of excellent adhesion, low contractility, no bubbles, impermeable, heat-resistance, melt-resistance, and without the phenomenon of lime efflorescence. In addition it can be instead of dry-hanging of marbles. We suggest that improve the cement standard or mix cement additive when stick marble, granite, or other big stones to improve the adhesion between plan surface and wall. PB-05 is suitable for sticking the stones which water absorption capacity is less than 5%. 
 

Features:

1. Well water-protective; Don\'t need to soak the brick and wall to improve work efficiency. 
2. Excellent adhesion, both to the wall and to the paint..
3. Maximum protection against leakage caused by moisture saturation; Excellent resistance to corrosion. 
4. Excellent elasticity, shrinking-free, no bubbles.
5. Resistant to the both positive and negative hydrostatic pressure. 
6. Its 3 times working speed than the traditional working way. 
7. Convenience to use; Non-toxic 
 

Surface preparation:

All surfaces must be structurally sound, dry, clean and free from movement, oil, grease, wax, curing compounds and any other loose or contaminating materials.
 

Stir and mix:

Add clean water to a bucket, then slowly add marble powder to the water. Stir the mix with electrical drill-mixer until a lump-free consistency is achieved. Allow the mix to stand for 3 to 5 minutes. Re-stir then use the marble adhesive. The mixing ratio is 20 kg powder to 5 liters of water. 
 

Application:

Scrape the mixing(thickness is about 3mm) on the surface with scraper; Each scraping area is about 1㎡; Then use scraper(10mm×10mm) to cut the surface to rack gear shape. Scrape the mixing (about 3mm) on the back of marble; Then use scraper (3mm ×3mm) to cut the surface of the marble to rack gear shape. Finally press the marble on the surface slowly. 
 

Precautions:

1. Make sure vertical and horizontal veracity of the surface before working. 
2. The marble must be stuck on the surface within drying time. 
3. Must be adjusting the marble within adjusting time in order not to affect the intention. 
4. Dispose redundant marble adhesive before hardening. 
5. The floor should be opened to light foot traffic or grout after 24 hours following the process. 
6. Don\'t apply marble adhesive in temperatures above 40℃or below 5℃.
7. Don\'t allow the adhesive to skin prior to laying the marble. If the adhesive skins, remove and dispose of it, then re-apply fresh adhesive. 
 

Remark 

Main ingredient:

Concrete macromolecule polymer.

Package:

20kg/bag 

Storage:

Shelf life is minimum 1 year when stored in covered and dry environment. 

Standard:

JC/T547-2004 
 

Technical Parameter:

Comply with standard JC/T 547-2005

Size of notched trowel