High Frequency And High Precision Electric Arc Welding Machine 
 
Quick Detail:
 
Box column welding machine is a special equipment which is gas shield welding for box column or submerged arc welding.
 
 
Description:
 
Box column beam welding machine is a special equipment which is gas shield welding for box column or submerged arc welding. For submerged arc welding and gas shield welding, the machine frame is common, but only matching different welding power and assistant device then realize different welding equipment. On the double-decker frame of the column beam welder trolley, it can be put welding wire support flame (or welding wire drum), welding flux recovery machine, cooling water box and other assistant device.
 
 
Specifications:
 
a. Structure principle
Using back welding to the welding seam bottom of the box beam is to prevent large current burning through bottom of welding seam, generally used the CO2 gas shielded welding.
And being similar with other structure, the cantilever back welding is composed of moving cart, column, cantilever beam, welding arm, welding seam tracking device, wire feeder, electric control system and the welding power, etc.
Moving cart is composed of one base, four moving wheel, and 2pcs of wheel axles, 2 sets of motors. 2 sets of motors drive four wheel axles through the gear. It composes 4 wheel driving systems, in order to make it stable and reliable operation.
On the base of a double-decker frame, you can put welding power on bottom and wire plate or wire tube on top.
The dimension of the column is large, so it makes the overall rigidity structure bigger. And the operation panel is on the electric box.
The main part of upper beam is square tubes and has light weight rigid good characteristic. The upper beams have guide and rack, so it makes dragging plate and welding beam moving levelly on the beam.
The cantilever box beam welding arm has two groups of two welding seam. It can welds two welding lines simultaneously. On the one hand it can drag on the board in the guide beam in translation, on the one hand, it can also drag on the plate wheel and mobile.
The welding seam tracking devices are installed below the welding arm. It can track welding line automatically to make welding torch and welding line keep proper distance. This device in horizontal direction adopts pneumatic tracking, and in vertical direction it automatically tracks by gravity.
The wire feeder is installed on the welding arm. It connects with wire plate, wire feeder and welding torch by wire tubes.
The electrical control box is install inside of vertical boom, operation panel is on the door of electric control box. The electrical control box is control the moving of cart, elevating of welding arm and power start/stop. The cart moving is frequency control. It can adjust the moving speed according to the welding technology.
Usually we use Tangshan Panasonic CO2 welding machine (YD-600KH), also you can select other brand. For single arc single wire, need two sets welding power for one set cantilever welding machine. If double arc double wire, that need four sets for one set of cantilever welding machine.
 
b. technical parameter
● Beam size: 300-1200 mm
● Welding speed: 0.15-1.5 m/min
● Return speed: 4.5 m/min
● Cart gauge: 1400 mm
● Main machine power: 1.4 kW
● Gas source pressure: 0.5-0.7 MPa 
 
c. Range of supply
● Cart part: moving cart, motor reducer, and vertical column, cross boom.
● Welding arm, carriage plate: welding arm, carriage plate, motor reducer.
● Welding seam tracking device: arc-guide frame, arc-guide wheel, and gas cylinder.
● Electric control system: electric control box, operation box, AC frequency converters.
● Pipe wire system: control cable, gas source pipe and slide wire frame.
● Welding system: Panasonic welderYD-600KH×4sets, control box, control cable and cooling water box (also can use other brand)
 
d. Technical documents
● Operation manual (elementary electrical diagram, foundation drawing)
● Certificate
● Frequency converters operation manual.
● Packing list
 
 

About Us:

1. Main electric elements are Siemens / Schneider.

2. Have strong design team, experience engineers supply good service.

3. Solve your technical problems in 24 hours and provide international warranty service for engines.

4. Design the appearance form according to customers’ request.

5. More than 13 years professional production experience, the quality is reliable.

6. CE and FCC certification.

7. Punctual delivery.

8. Accept OEM and ODM requirements.

9. Accept testing before delivery.