Delivery Time:3-5 workdays after payment

RFID Learning Arduino Starter Kits For Stepper Motor Learning

RFID learning kits ,stepper motor learning KIT FOR ARDUINO Arduino Starter Kits

Quick Detail:

ARDUINO RFID learning packages using ARDUINO UNO R3 this latest control panel,

ARDUINO microcontroller allows users to learn from the boring when theoretical knowledge,

In the play in the development of the ability to obtain RFID SCM system.

Specifications:

This package contains the following components:

ARDUINO UNO R3 board * 1

High quality and large bread board * 1

RFID module * 1

IC Keychain * 1

Non-contact type IC card * 1

I2C 1602 LCD module * 1

5V Relay * 1

DS1302 clock module * 1

Voice detection module, * 1

Temperature and humidity module * 1

Level detection module, * 1

4 * 4 keypad module * 1

Three-color RGB module * 1

XY joystick * 1

Servo * 1

Stepper motor driver board * 1

Blue LED * 5

Yellow LED * 5

Red LED * 5

1k resistor * 5

10k ohm resistor * 5

220 ohm resistor * 8

Buzzer * 2

Key module (with hat) * 4

ROCKER SWITCH * 2

LM35 sensor module * 1

Photoresistor * 3

Fire * 1

Infrared receiver * 1

Adjustable potentiometer * 1

A digital control * 1

4 digital tube * 1

8 * 8 dot matrix module * 1

74HC595N chips * 1

Infrared remote control * 1

Breadboard Jumper 30

Male to Female DuPont lines * 30

9 volt battery snap * 1

USB Cable * 1

The Arduino Uno is a microcontroller board based on the ATmega328 . It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.

The Uno differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 (Atmega8U2 up to version R2) programmed as a USB-to-serial converter.
Revision 2 of the Uno board has a resistor pulling the 8U2 HWB line to ground, making it easier to put into DFU mode.

Revision 3 of the board has the following new features:

 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Arduino Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit. Atmega 16U2 replace the 8U2.

\"Uno\" means one in Italian and is named to mark the upcoming release of Arduino 1.0. The Uno and version 1.0 will be the reference versions of Arduino, moving forward. The Uno is the latest in a series of USB Arduino boards, and the reference model for the Arduino platform.

Summary of 2012 UNO R3 Board

Microcontroller	ATmega328
Operating Voltage	5V
Input Voltage (recommended)	7-12V
Input Voltage (limits)	6-20V
Digital I/O Pins	14 (of which 6 provide PWM output)
Analog Input Pins	6
DC Current per I/O Pin	40 mA
DC Current for 3.3V Pin	50 mA
Flash Memory	32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM	2 KB (ATmega328)
EEPROM	1 KB (ATmega328)
Clock Speed	16 MHz