Reci 80W 100W 130W 150W laser equipment parts laser cutting machine parts of laser cutting machine co2

Reci 80W 100W 130W 150W laser equipment parts laser cutting machine parts of laser cutting machine co2:

40w/60w/80w/100w/130w laser tube

90w/100w/130w/150w RECI laser tube

Control card
Reflector
Focus lens
Laser supply

motorized up-down table 
special water cooling chiller cw 3000/5000
rotary axis 10cm /20cm
honeycomb table

water chiller
air pump

stepper motor
Servo motor
Driver

Draught fan

If laser tube broke in shipping by DHL our company will send new one no charge!

 Cardboard Carton  Package Size

 
  Laser Tube basic parameter 

Package: Free-fumigation wooden cases or other customized packages.

1.We will provide the user a CD to study the machine installation and commissioning of English.

2.Our technicists can give user online guide.

3.The user can by call or email us any problems at any time.

4.One year warranty for machine maintenance, for equipment maintenance over the warranty period is clearly marked.

Our company was established in 1994,we are manufacture and specilized in laser engraving and cutting machine,cnc router,plasma cutting machine and cutting plotter.From 2007,we have expanded our bussiness to worldwide.In the past 12 years,so many clients all over the world cooperated with us and built a good business realtions.We have much experiece on our after-sale problems.

1.Installation Requirement
Make sure to follow the operation instruction of model Z4 as shown in the illustration. The dedicated power DY13 should be equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv).
 It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage.

2.Operation conditions
Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40℃The operating environment: temperature 2-40℃; humidity 10-60%The working current: test current is 30mA. Maximum working current is 30mA. The running current
must be kept below 28mA. The life span can reach 10,000 hours if the current is kept below 26mA.
 The ammeter must be connected to the negative electrode of laser tube.When it is working under over-high current for long term, the negative pole will appear brown yellow, and the life span will be
shortened rapidly.To protect dust from going into the insulation sheath, please wrap it with plastic film.

3.Working Performance
Cutting function.Engraving function: Very good. When the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.

4.Key Notes
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted. Attention: it is forbidden to clean the mirror with acetone.
The screws in the front and back ends of the laser tube are not allowed to be moved,
otherwise the out power will be declined, even the tube will be scrapped.
Put the acryl 300mm far away from output mirror, when testing its laser spot.

5.Safety The laser beam is invisible light. Please wear protective glasses when debugging the laser.
The positive pole is in high voltage. Pay attention to the security marks.

6.Storage and Transportation Requirement
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way. Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from vertically sliding during transportation.
The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider.

7). Personal contact ?

Whatsapp:008618765893695

Skype:2945996115 @qq.com

               CNC Router Machine                                                                        Stone and Wood CNC Router Machine

        More Spindles CNC Router Machine                                                             Laser Cutting and Engraving Machine