Chengdu Weegiant Weeson

highest quality 3 years life span 130w CO2 laser tube for cutting metal and nonmetal

The Laser Tube product is ordering production, need 3 to 5 days of stock up time.

High power rate, fast - speed cutting and small size 
Origin: Asia and Pacific Area China
Quality standard: International

H.S. Classification: 
Machinery & Electronics Electr. Element 8541 Semiconductor devices; light - emitting diodes etc.
Mark & model: P6, the product is featured as large power rate laser tube, good stability and fast cutting speed, which is suitable for the cutting of thin metal plate.

We will send a new one freely if the tube is broken during transit.
Once received the laser tube, please check again at the first time. 
We need the damaged record from the courier as the proof before we send the new one free.

Output Power: 
Its output power can reach 150w. The production process of the tube is standardized, so the output power and output model are guaranteed. (For other laser tube manufacturers: can’t provide this product)

Long life span: 
We have catalyst plating in the inner wall of the laser tube. The warranty is 3 months.

High performance cost ratio: 
High output power, high efficiency, and high performance cost ratio.

High photoelectric conversion rate: 
The output power decrease rapidly when the cooling water’s temperature is 42°C. Its heat productivity is lower than 100w tubes of other brands. 

Appearance: 
Its unique appearance makes the tube light and slim, doubles its anti-distortion ability and increase its working stability.

Variable outer diameter: 
With variable outer diameter, it is widely applicable for various machines.

Length: 
The length is only 1.65m. It reduces the volume of the machine and minimizes freight cost.

Chengdu Weeson R6 CO2 laser tube is featured as high power rate, good model, and fast - speed cutting and small size, which is used for the cutting of die-cutting plate, thick acrylic plate and so on, widely used in packaging industry which uses large quantity of medium density fiberboard and plywood cut by die-cutting machine as well as advertisement industry with the widely usage of light guiding plate and display screen.

High photoelectric conversion rate: 
Its heat productivity is lower than 130w tubes of other brands. The output power decreases rapidly when the cooling water’s temperature is 42°C.

Warranty: 
3 months, international warranty service, Chengdu Weeson charges the freight for exchanging the defect tube.

High performance cost ratio: 
When you buy Chengdu Weeson R6 130W Laser tube, you can spare money for transport. Besides, you get 3 months warranty and the top level after sale service.

Operating Instruction
Installation Requirement
1. Make sure to follow the operation instructions of model R6 as shown in the illustration. The dedicated power T150 should be equipped. The positive pole is in high voltage (The ignition voltage is 30kv). It may cause the following consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause water leakage. 

2. Operation conditions
• Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40°C.
• The operating environment: temperature 2-40°C, humidity 10-60%.
• The working current: Test current is 26mA. Maximum working current is 30mA. The running current must be kept below 27mA. The life span can reach 10,000 hours if the current is kept below 26mA. The ammeter indicating current must be connected to the negative electrode of the laser tube.
• When it is working under over-high current for long term, the negative pole will appear purple, and the life span will be reduced rapidly.
• To protect dust from going into the insulation sheath, please wrap it with plastic film.

3. Working Performance 
• Cutting function.
• Engraving function: Very good, when the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.

4. Key Notes 
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideway with air blower. 
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized. 
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted. 

Attention: 
It is forbidden to clean the mirror with acetone.
The screw in the front and back ends of the laser tube is not allowed to be moved, otherwise the out power will be declined and even the tube may be scrapped.
Put the acryl 300mm far away from output mirror, when testing the laser spot.

5. Safety 
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks.

6. Storage and Transportation Requirement 
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40°C, and the requested humidity is 10-60%. Pack the laser as in the original way. 

Important notes: It is requested to cement the sponge together with laser tube to prevent the tube vertically sliding during transportation. The sponge in the side of output mirror must be 70mm beyond it, and the sponge in the side of reflecting mirror must be 50mm wider. 

7. Tubes operated in wrong way will not be guaranteed by manufacturer. 

How to check the laser?
The laser power will reduce gradually while using. When the maximum power can’t carve deep enough, please change the laser tube.
We need to exclude other reason of the problem. 
Firstly, make sure following things: Cooling - water flows well and bot hot or dirty. When water temperature is higher, laser’s power will drop fast, or even explode the laser. At this time, change it or add more cooling water.
Secondly, make sure the mirrors, lens and light rought are all good.
Thirdly, make sure the electrical power and fanners is working well. When the temperature of electrical power is higher, it will afect the laser.
In fact, laser’s power will reduce slowly. When the laser is all right, light beam in the tube is pink - purple, when it’s near to be finished, the light change to with.
 

 Wooden Box: There is total one wooden box. 

Package