Main Products: Granite ,Marble ,Quartz stone ,Granite countertop ,Stone
China brown granite royal pearl
USD $10 - $30 /Square Meter
Min.Order:200 Square Meters
Quick Details View All >
Business Type: Trading Company
Xiamen Fujian ChinaMain Products: Granite ,Marble ,Quartz stone ,Granite countertop ,StoneProduct Details
China brown granite royal pearl
Part One: Product Info.
| Product Name | granite royal pearl |
| Place of Origin | China |
| Stone Form | Cut-to-size tile |
| Color | brown |
| Finishing | Polished, Honed, Flamed, Sandblasted, Bush hammered, Rough picked, Mushroom, Chiseled, Natural split, Grooved, Acid treatment etc. |
| Edge | Eased, Beveled, Bull nose, Ogee, Cove, Dupont, laminated, non-laminated and etc. |
| Size | 30x30cm |
| 40x40cm | |
| 40x60cm | |
| 60x60cm | |
| Other custom sizes | |
Thickness | 10mm,15mm,18mm,20mm,30mm,40mm,50mm, as per customers’requirement |
| Payment | 30% deposit, balance against copy bill of lading |
| Packing | Plastic film and foam inside, wooden crate outside. |
| Minimium order | 100M2 |
| Lead time | Usually 25 days |
2. Part Two: Finished Products
Part Three: Quality Control
| Quality characteristics: |
| 1.thickness tolerance = ±1mm; length and width=±1mm. Spots, splits, damages and chips are not accepted. |
| 2. Tiles size tolerance: length and width=±1,0mm. |
| 2.1 Thickness 15mm - tolerance = ± 1,5 mm. |
| 2.2 Thickness 20mm and more - tolerance = ± 2,0 mm. |
| 3. Angle between 2 contiguous edges is 90 deg. |
| 4. Dyeing or color enhances are not allowed to use. |
| 5. Polish degree for polish surface - 80 up. |
| Package and loading requirements: |
| 1. Gross Weight of the following goods: tiles, steps, risers package should not exceed 1100kgs. Gross Weight of paving stones package should not exceed 1500 kgs. The buyer agreement should be obtained in case packing over those limits. |
| 2. Attached crate's sheme is inalienable part of this PI. The wooden crate to be produced according to scheme as per attached crate's sheme. |
| 3. Crate wood material should be good qulity, spunk is not accepted. |
| 4. Crate frame board thickness - at least 20mm. |
| 5. Crate bearing bars are should be at least 50*60mm in cut. Side bars to be located at the ends of crate. Central bar to be located at the center of the crate between two side bars. |
| 6. Crate frame must be knocked together tightly and fasterned with wide metal stripe (clip) in the lower and upper part of vertical edge corner as per attached crate's sheme. |
| 7. Diagonal purlin bars must be located on the crate as per draw attached crate's sheme. |
| 8. Nails should not be knocked close to the board edge to avoid chips and damages of the products. |
| 9. There are no manufacturer trade mark on the crate, “N/M” should to be written instead of your company name. |
| 10. Products to be wrapped with protecting film. |
| 11. At least 7 plastic/metal bands (2 inner + 5 outer) to be applied for each crate. Bands are to be tight and fastern the crate. Slack is not accepted. |
| 12. Tiles package and stowing requirements: |
| 12.1. Tiles must be stowed face to face each other in vertical position. |
| 12.2. Stowing into crates: |
Part Four: Factory/ Loading/ Certificate
Contact Supplier
You May Like
New Products
Popular Searches
Recommended Products
Find Similar Products By Category
Facebook
X
Pinterest
Linkedln