System structure

Summarize of the system

   General control system is a kind of intelligent control system that corresponds with the indoor and outdoor scene lighting control ,like hotel lighting and building lighting control. The whole design scheme is based on operation humanized and personalized principle. The system can control all the lighting system by computer network, monitor the current operating state of each lighting subsystems, achieve linkage control with DALI system, DMX system, multimedia central control system,485 bus and TCP/IP. At the same time it can be extended to the intelligent control of the entire home or commercial systems.

Product name:Centralized Manager for dmx 512

Model No.: LYE100

1. Summarize of the product

This product through EDX interface connected to the scene panel, through DMX - 512 interface and DMX dimmer or switch controller connection, network interface provides remote online and setting function.

A, Output DMX 512 signals, can control 512 circuit, and throuth DMX OUT monitoring function to test circuit state.

B, Can set up model of guest rooms and public space/can set the password protection function.

C, Can match ECP series control panel.

D, Can store 896 set of scenarios, each group can control 512 circuit scene.

E, Can set if receive DMX signals.

F, Can be set 128 areas,suitable for all the kinds of places.

G, Can beused to match figure control software.

2.Technical Parameters

3. External dimension

4. Interface specifications

1) The alternating current input

2) The alternating current input

3) The alternating current input

4) 12V power output

5) EDX signal A

6) EDX signal B

7) GND

8) 12V

9)  DMX signal A

10)  DMX signal B

11) GND

12) Input signal light

13) Power light

14) Input signal light

15) Increase button

16) Reduce button

17) Turn back button

18) Turn front button

19) Confirm button

20) Program download interface

21) Internet access Interface

22) USB

5. Use instruction 

5.1 The host interface Operating instructions

1) System time

2) Currently running area number

3) The current operation area is the scene

4) Select function button 

5.2 Mode scene 

Operation instructions

Touch function key to enter MODE scene, please refer to previous picture for the
following operating.
Touch “Call scene”, enter the regional scenarios scene.
Touch “Scene”, enter the scene configuration screen, configuration corresponding to
the CP, SC of fades DMX512 , fading time, scene model.
Touch “DMXOUT”, enter the interface of view the DMX512 current output
Touch “Calendar”, enter the date of the timer interface, Configure the timer
Touch “Astro”, enter the astro of the timer interface, Configure the timer
Touch “Timer”, enter the timer switch interface
Touch “Clock”, enter the system clock interface
Touch “Patch”, enter the system patch interface
Touch “Address”, enter setting IP address interface.
Touch “Password”, enter setting password interface

5.3 Call scene

Under the MODE interface touch “Call scene “into the selected regional scene
interface , you can make the user to configure each scenario

CP:display area, SC:display the selected scenario

On the left,as picture 1,“regional selection area”,Through touch or up/down button to
select, the selected area display on “CP” position.

On the right,as picture 2, “scene selection area”, Through touch to select scene, the

selected scene display “SC”position.

On the down,as picture 3,setting back function scene.

5.4 Scene Operation instruction

1 ) Under the MODE interface touch “scene “into the selected scene interface.
2 ) Display the current selected area, through up/down key to select the area
3 ) Display the current selected scene, through up/down key to select the scene
4 ) Display the current selected fading time, through up/down key to select the time
5 ) Display the current scene mode, SW, SC two kinds
6 ) The current channel number:0-100 or NC, can slide to adjust
7 ) Touch to turn paper, also can through right/left key
8 ) Touch to turn paper, also can through right/left key
9 ) Back function scene.
10 ) Confirm to store the scene data.

5.5  DMXOUT SCENE

1) Under the MODE interface touch “DMXOUT” into scene, check current 512 output
number
2) Initial channel coding
3) The output number of the corresponding channel
4) Turn-back, also through right/left key to turn
5) Turn-front, also through right/left key to turn
6) Back function scene

5.6 Calendar Scene

Under the MODE interface touch “Calendar” into scene .As the picture, dispaly
“ADD”AND “EDIT”

Touch ADD into the following scene.

 6.Assembly method

 1.We are located in Baoan district, Shenzhen City,China,closed to the shenzhen airport,convenient for the visit !

2. Years  menber of Alibaba

3. Products are approved with CE,RoHs,Fcc,SAA,UL ,ETL certificate.

4.Every year we attend the  Guangzhou optical sub Exhibition 

We adheres to "convenient, efficient, intelligent" which guarentees products quality and customer service. Intelligent integrated into life, make life more convenient.

 2,All of our items have  years quality warranty. Offering the customer best services prior or after sale

 3,Samples shippment can be settled 1-3 days after ordering and payment.

 4, OEM welcomed!!