What's charcoal briquette extruder machine:

Charcoal briquette exturder machine is mainly used to use the screw extrusion principle to process 

carbon powder mixed with a certain proportion of liquid binder into different bar shapes and size of briquettes, with certain strength, also you can choose to make the briquettes with or without a hole in the core part. The utilization of this machine can make full use of the coal powder material, you do not need to mix the material with lime, it reduces the cost of fuel, and improves the calorific value of raw material.

Features of charcoal briquette extruder machine:

1). First carbonization, and then briquetting, reduces the procedures to 3 stages from the 5 process of firstly briquetting and then carbonization.

2). The service life is greatly prolonged, especially the quick-wear parts, the service life is increased from 40 hours to 4000 hours.

3). The cost of electricity is reduced by 60%.

4). The capacity is increased by 2-3 times, the cost of making charcoal briquettes is reduced.

5). The operation of the machines is become very easy, we show you directly in front of you, or by videos.

6). The carbon is turned into high quality carbon briquettes, the high quality coal is turned into special high quality carbon.

7). The weak carbon content is increased from 60% to 70-75%, the high quality carbon content is increased more than 83%, make the market highly expanded.

Material information of charcoal briquette extruder machine:

1. Applicable raw material: different charcoal powder of biomass material such as: sawdust, wood shavings, wood wastes, branches, rice husk, peanut shell, coconut shell, begasse, sediment, cotton stem, corn stalk, corn cob, etc. After carbonization, the charcoal can be used as raw material. Besides, the carbon black, coal powder, coal dust, coke powder, brown coal powder, coal waste can be also used.

2. The inlet particle size of raw material: it must be less than 2mm.

3. You must add a certain proportion of liquid binder of some kinds of materials for shaping easily, besides, the binder can also increase the hardness of material, and make the briquettes easily burning.

4. The moisture of materials for briquetting must be moderate, the water content should be 12-15%.

Technical parameters of charcoal briquette extruder machine:

Model 140

Model 180

Model 300

Installation of charcoal briquette extruder machine:

1. All the part should be cleaned and checked before installation.

2. Install the machines on the level ground, and better on the concrete floor.

3. Before trying the machine, you have to add oil into the lubricant parts.

4. Check whether there is loosen parts, if yes, tight it directly. 

5. Inching the machine, and see whether there are clutters and unnormal sounds. If there is no, we can start the machine completely.

6. Driving the machine to run it without any material in for about 3-5 minutes, after make sure the machine works normal and good, we can put the materials in it for production.

7. If the feed opening apperas blocking, use a wooden stick to unclock, and mustn't use the metal of steel stick.

8. Add the oil for the transmission and rotating parts regularly. The temperature of bearing parts shold be less than 60 celsius degree.

9. Stop feeding the materials and make sure there is no any material in the cylinder before stopping the mahcine. Remove the machine head, clean it and theninstall it for next time using.

Carbon briquettes:

Assistant machines of charcoal extruder briquette machine:

1. Firstly, you need to crush the powdery material into small size: which should be less than 2mm.

2. Secondly, you need to make liquid binder, to increase the hardness of powdery material, and also make the raw material easily burning.

3. Thirdly: you have to mix the liquid binder with the powdery material evenly for that the powdery material can be easily and better pressed into briquettes.

4. Forth: you can feed the raw material into the briquette machine directly, or use the auto feeder to feed the material evenly into the briquette machine.

5. Fifth: you shall dry the charcoal briquettes by our box-type dryer, or dry it under the sunshine if it is dtrong enough.

Brief introduction of the assistant equipment for this line:

1) Crusher:

It is used to crush the raw material into powdery material for briquetting, the size must less than 2mm, and the smaller, the better the briquettes. This is the first step of making briquettes, this machine is an environmental protect extraction device, which can totally keep the powdery carbon black, not only can save material, but also protect the environment.

2). Binder Mixer and Wheel Mixer:

Binder mixer is an special equipment for this production line, to make the powder easily briquetting, and also increase the hardness of the powdery material. Besides, it ca also make the briquettes easily burning, and the briquettes are smokeless, non-toxic.

Wheel mixer is to mix the powdery material with the liquid binder, but also can grind the charcoal powder to increase its hardness and strength of the briquettes.

3). Auto Feder:

It is used to feed the raw material into the briquette machine for briquetting evenly, to avoid the conditions that too much material jam the machine or too little material can not briquetting.

4) Box-type Dryer:

This machine is used to dry the charcoal briquettes produced by the screw carbon briquette press machine, also you can dry the briquettes under the sunshine if it is strong enough!

Packaging and shapping of our machines:

Our payment terms:

1. We usually accept T/T, or Cash. 30% for down payment, and 70% pay as balance before loading.

2. It is about 15-25 days to finish all the machines after receive the down payment.

3. We take pictures of finished products, and test all the machines before delivery.

Packaging of our machines:

1. Stand blasting, coat with high quality paint;

2. Product wrap by film;

3. Load container, machines and Spear Parts in wooden case.

4. as your special requirements.

Delivery of our machines:

1. We have been long term of cooperation with many famous shipping agent. Also we can according to your needs to arrange the delivery.

2. After load the machines into the containers, we can we send the loading pictures to you.

3. When we get the BL after the ship leave the Port to your place, we will send it with the Contact, Pre-form Invoice, Packaging List, etc to you so as your can do the clearance.