Wholesale Scrap Copper Wire Stripping Machine Free Shipping Waste Cable Wire Recycling Machine

1. Introduction

2. Use Instruction 

  Push the Switch up to turn the Motor ON, Check whether the machine work well. Make sure there are no people on the output side of the machine. Comparing the cables/wires’ diameters with the feeding holes on the machine, feeding the cables/wires one piece at one time.

1,Before feeding the cables/wires, please cut off the head of the cables/wires, to avoid gaps caused to the blades.

(1) On the output side, if the cuts on the cables/wires are too deep, please check below points:

(2) Please adjust the handles on the input side, screw down or loose them.

(3) Check whether the cables/wires on the right position as you feeding them.

 Make sure the blades are sharp, if not, polish  them with the oil stone

 2,On the output side, if see the plastic (PVC) has been stripped, but the copper wires can not been disgorged, please check below 4 points:

(1) Polish the axis of the upper side shaft with the oil stone properly.

(2) Check whether the springs are loose, if yes, screw down to make them tighten

(3) The diameter of the cables/wires are too small, please adjust the space between the two axis to 0.3-0.6mm.

 If the cables/wires you want to strip are hot, also can not get the copper wires stripped out.

3,If the cables/wires were blocked in the axis, please check below points:

(1) Check if the V-belts are loose.

If the springs on the press wheels are too tight, loose them.

(2) There are too much oil on the cables/wires, please wipe it(make sure the machine is turned off when you wipe the axis)

4,If see the blades tilted:

(1) Check whether the center adjuster was loosed.

(2) Centering adjustment and adjust the screws of two sides of it.

1,Blades adjuster                A:twin-core sheet wire inlet

2,Wheel adjuster                 B:3-4 cores sheet wire inlet

3,center adjuster                  C:Diameter 1.5-3.0mm cables/wires’inlet

4,Safeguard meshwork      D:strip video cables/wires or core loosed wires

   E:Diameter 3.1-4.5mm cables/wires’ feeding  hole

   F:Diameter 7.0-10.0mm cables/wires’ feeding  hole

   G:Diameter 10.0-13.0mm cables/wires’ feeding  hole

   H: Diameter 13.0-14.0mm cables/wires’ feeding  hole

   I: Diameter 14.0-16.0mm cables/wires’ feeding  hole

J,K:dual core flat wires

K:  Diameter 1.0-3.0mm cables/wire’s feeding hole

L:  Diameter 2.0-6.0mm cables/wires’ feeding  hole

M:  Diameter 3.0-8.0mm cables/wires’ feeding  hole

N:  Diameter 5.0-10.0mm cables/wires’ feeding  hole

O: Diameter 6.0-12.0mm cables/wires’ feeding  hole

P: Diameter 10.0-15.0mm cables/wires’ feeding  hole

Q: Diameter 12.0-20.0mm cables/wires’ feeding  hole

R: Diameter 15.0-27.0mm cables/wires’ feeding  hole

S: Diameter 25.0-33.0mm cables/wires’ feeding  hole

T: Diameter 30.0-42.0mm cables/wires’ feeding  hole

1.  We only for manufacture environment friend recycling machinery.

2.  We are professional supplier and manufacturer of recycling machine 21 years.

3.  We have professional technology to guide produce of machines.

4.  Our products are exported to all over the world, such as European, South America, North America and so on.

5.  We have many agents in lots of countries.

6.  CE certification

1. We offer 24 hours superior service to clients.

2. We Provide high quality for clients according customer demands.

3. We will response any question about products in all the price lists are only for references. 

If you are interested in our products - cable/wire stripping machine BS-015M, please contact us freely and directly . We will provide the most professional service to solve any of questions you may raise. 

1. This advantage for product?

Reply: High efficiency , energy saving and good quality.

Reasonable price and best services , advanced equipment and strong technology.

Do not hesitate to contact by online or Email as soon as possible once you are interested in our products. The specific quotation will be offered basing the request dimension and quantity

2. What about the quality?

Reply: All products according to ISO and National highest standard, also we can offer CE, certificate if necessary. The machine have one year warranty.

3. What payment is available?

Reply: L/C at sight, or T/T 30% deposits before production and 70% balance to be paid before shipment.