Shipyard can accommodate specific operating environment, namely in wet, corrosive, dusty, high temperature, low temperature environment.

· Boom in any position, work platforms are safe to walk; walking speed with increased lift height increases.

· Has upper and lower console (console and floor console platforms) and the upper and lower console commutation switching. When the upper portion of the lower part of the console to control the use of locking function.

· Console diesel engine oil temperature, oil pressure, water temperature, etc. indication.

· Provided under Anti engine operating condition means starting again.

· Telescopic boom, luffing, slewing runs smoothly and has a cushioning device.

· Telescopic boom, luffing, slewing and traveling platforms are used electro-hydraulic proportional control enables stepless speed.

· Walking and boom slewing platform shall be provided with reliable brakes, and ensure that the process is running on ramps can be reliably controlled. Installation manual rotary locking and releasing walking braking, so the platform is pulled.

• When walking platform, if a case vacated by dispensing valve, the other driving wheel can walk alone.

• When working arm angle above the horizon or telescopic arm extends more than 1.2 meters of walking speed of the vehicle is limited.

· Telescopic boom, luffing, slewing platform and can walk much work simultaneously.

· Working bucket with automatic leveling feature, the tilt angle of the bucket relative to the horizontal plane of the work can not be greater than 1.5 °.

· Upper and lower console has an emergency stop button, when the operation of unforeseen circumstances, the operator can quickly extinguish engine platform to continue to avoid exercise.

The platform shall be provided on the foot switch, only depress the foot switch in order to operate.

· Has a 24V auxiliary power unit, when the engine or main pump fails, to make work safe bucket lowered to the ground.

· Has a torque limiter, control operating range bucket work, limitations and extend working arm angle reaches the magnitude of the job, ensure the stability of the vehicle.

· Digital dual sensor detector circuit timely detection length, angle and other parameters, dynamically reflect the working condition of the boom. When one circuit fails, the other can still complete the circuit to detect all parameters.

· Working with a bucket weighing function, accurate detection of the load platform, regardless of the position of the load on the platform. Should have two or more load capacity, different load allows different operating amplitude range. When the maximum permissible load of the platform load exceeds the corresponding amplitude state, should be able to display and alarm and limit movement of the platform to ensure that work and work bucket bucket connection strength and job security.

* With automatic transmission and alarm off function: When the amplitude reaches or exceeds 80% of the amplitude of the corresponding permit, all the action will automatically reduce speed and is accompanied by a buzzer and flashing alarm, and the closer the magnitude of the maximum limit, the more speed work low, the buzzer sounds sound more rapid. When the working range up to 100% of the maximum allowed magnitude, it will automatically stop all the dangerous direction of movement.

· There should be three engine throttle control gear speed, when a long time without any action, the engine is automatically reduced to low idle, meet the energy requirements.

· When the machine is parked at the unevenness of the ground more than 5 °, jib action will be limited.

· Equipment walking and turning, it will be audible and visual alarm.

Adopt PLC and CAN bus control mode, simplifying the wiring, easy maintenance and repair. Metal plug air defense, protection grade IP65.

· Engine air intake system in a closed two-stage filtration, dusty environment to adapt to the job; and easy maintenance.

· Upper and lower console should have shields to protect.

· Boom head, cylinder piston rod, etc. There are dust and sediment retention device.

· Pump with automatic pressure compensation and load sensing function, to ensure that the oil pump and the engine will not be damaged due to overload.

· Provided to prevent overheating of the engine and hydraulic oil pressure is too low, automatic stop device.

· Install a safety valve in the hydraulic circuit to prevent abnormal pressure rise in the hydraulic components.

· Each cylinder has a balancing valve cylinder or hydraulic lock does not automatically guarantee the operation, and the fuel tank with the balance valve, hydraulic lock connection is rigid.

· Hydraulic components and control components imported brand products, high reliability.

· Towline institutions using patented technology sleeve, the sleeve for the aluminum alloy surface treatment, towline maritime resistant high-strength plastic, to adapt to harsh working environment.

· Undercarriage and turntable position with rings for easy lifting.

Standard configuration

Automatic amplitude limiter,Weighing apparatus,Automatic leveling,Tire telescopic shaft

4-wheel drive,4 steering,High and low speed walking,Full proportional control

Uneven ground protection systems,Emergency drop system,Rotary table

Stage anti-collision protection,Engine restart protection,Engine warm-up protection

Three engine throttle control,Hydraulic oil cooler,Dust protection,Solid tires

Strobe,speaker

Optional equipment

2 drivers,2 steering,Perkins engine,Ventilation table

Workbench energized,Platform work lights,Foam tires

Descriptions Of Compact structure electric scissor aerial work platform lift promotion

1.The Mobile Scissor Lift is mainly used for lifting cargos and delivering goods,high-altitude operations.
2.An ideal equipment of safe operation
3.It is charactrized by great loading capacity.
4.Steady ascending and descending
5.New hydraulic system increase safety and protects 4M-18M hydraulic mobile scissor lift 
6.Mobile convenient ,easy to work.
7.Economy and practicability.
8.It is applicable in the warehouse and garages and port ,building and so on.

Shenchuan (Shanghai) Heavy Industrial Machinery Co., Ltd. was established in May 2003 in Shanghai. Over the past 10 years, we have been always adhering to the idea of “all service to meet customers’ needs”, breaking through technology, manufacturing the finest products, improving service with our globalization vision.

We have developed a variety of international advanced products joint with world-renowned industrial equipment manufacturers, such as: ABB, ZF, BOSCH, CAT, TEREX, and a variety of sophisticated products with independent intellectual property patents together with well-known Chinese universities in the area of machinery, electronics, physical mechanics etc.

We will provide comprehensive and multidimensional supply chain service for global customers with our most optimized scheme, best quality products, most attentive service and most competitive price, to reduce the maximum supply chain cost for customers and increase the production efficiency.