Specifications

6802 ceramic bearing
1.Bear high temperature
2.Cold resistance
3.Best durability
4.ISO:9001:2000

6802 ceramic bearing use in medical equipment

Descriptions and specifications of 6802 ceramic bearing

6802 Full Ceramic Ball Bearing Silicon Nitride 15 x 24 x 5 mm

6802 Full Ceramic Silicon Nitride Ball Bearing, the inner diameter is 15mm, outer diameter is 24mm and the width is 5mm, this is a popular size that could be used in many applications, Bearing is made of Silicon Nitride Ceramic. Item: 6802 Ball Bearing Type: Full Ceramic Silicon Nitride Balls: Si3N4 Ceramic (Silicon Nitride) Inner/outer races: Si3N4 Ceramic (Silicon Nitride) Cage: No Cage Dimensions: 15mm x 24mm x 5mm/Metric ID (inner diameter)/Bore: 15mm OD (outer diameter): 24mm Width/Height/thickness: 5mm Size: 15 x 24 x 5 mm Quantity: One Bearing Highest Temperature: 1472 Degrees F Non-Magnetic Non-Conductive

 6802 Ceramic Bearing

 

The quality of bearing can be defined by various ratings, such as the rating of ball roundness. A high quality steel ball bearing is consider grade 25. The grade number refers to the tolerance per millionth of an inch. A grade 25 is accurate to 25/1,000,000 of an inch. Less expensive ball bearings may be grade 300, which are less round, at 300/1,000,000 of an inch. Ceramic bearings may be grade 5, which is a rounder ball bearing. The importance of roundness, however, should not be overrated, as the bearing surfaces the balls run on are unlikely to be as accurate as the grade of the ball bearing. The ball bearing is typically not the "weak link" in the system.

Another aspect of the bearing is the property of the material. There is a rating for hardness called the Rockwell scale. Steel uses what is called the Rockwell C scale, and ball bearings are of course hard. This hardness allows them to rotate and not wear, at least for a while. The bearings surfaces of the hub cone and cup typically have a Rockwell C rating of 55 to 60. A steel ball bearing is likely to be over a Rockwell C of 60. A ceramic ball bearings can be a Rockwell C of 75, much harder than the steel races. This should provide good wear features for the entire bearing system, not simply the ball bearing itself.

The surface finish of a bearing is also important. Ceramic bearings are not necessarily smoother than steel balls. In the image below, a Grade 25 steel bearing is magnified 200 times (Figure 2). Grind marks are apparent. In the next image, a ceramic bearing also show grind marks (Figure 3).

The ceramic material used in a ball is made of a grain structure, similar to a steel ball bearing (Figures 4 and 5). An important property of any material is "stiffness." This is a measure of how it deflects under stress or load, and the rating of this property is called the "Modulus of Elasticity." A steel bearing will be perhaps 30,000,000 pounds per square inch. Ceramic bearings made from silicon nitride can have a Modulus of Elasticity of 47,000,000 pounds per square inch. This extra stiffness means the balls will deflect less under load and this will transfer energy better, proving a (small) savings. While the ceramic ball is about one-half the weight of a steel ball the same size, it is the stiffness that is important in their performance.

 

It terms of service, there is no special procedure or process. Bearing can be cleaned and lubricated as normal. Loose ball bearings are installed and adjusted as with steel balls. Install bearings and fully cover with grease.CLUNT PPL-1 and PPL-2 is compatible with both steel and ceramic bearings (Figure 6).

With cartridge bearings, it is possible lift the seal and check the grease. Remove the spindle or axle first. For many cartridge bottom bracket bearings, it is necessary to carefully remove the a plastic shield over the bearing. Use a seal pick to lift the rubber seal from the inner edge (Figure 7). Wipe the bearing clean with a rag and then add grease. Press seal into place.

Applications of 6802 ceramic bearing

 Ceramic bearing wih high temperature resistance,Cold resistance,abrasion resistance,corrosion resistance,insulation,since gravity oil lubrication,high speed,etc.Can be used for extremely bad environment and the special conditions,can be widely used in

aviation,spaceflight,navigation,petroleum,chemical industry,automobile,electronics,matallurgical,power,textile,pumps,medical equipment,scientific research and defense,military and other fields,application of new material is high-tech products.Ceramic materials,zirconium oxide(Zr02),the azotized silicon carbide Si3N4(Six),three.Keep the PTFE,nItred,stainless steel or special aviation aluminum manufacturing,thus expanding the ceramic bearing applications

Model numbers

 

new modle	old modle	d	D	width (mm)	Cr	Cor	grease	oil	weight
		(mm)	(mm)		(kN)	(kN)	(r/min)	(r/min)
6207	207	35	72	17	25.7	15.4	9200	11000	0.288
6307	307	35	80	21	33.4	19.3	8500	10000	0.457
6407	407	35	100	25	55	31	7200	8600	0.952
61808	1000808	40	52	7	4.95	4.2	12000	14000	0.033
61908	1000908	40	62	12	13.7	9.95	11000	13000	0.112
16008	7000108	40	68	9	12.6	9.6	9000	11000	0.125
6008	108	40	68	15	17	11.8	9000	11000	0.185
6208	208	40	80	18	29.5	18	8000	10000	0.368
6308	308	40	90	23	40.8	24	7000	8500	0.639
6408	408	40	110	27	65.5	37.5	6300	8000	1.221
61809	1000809	45	58	7	6.4	5.6	9000	12000	0.03
61909	1000909	45	68	12	14.1	10.9	8500	11000	0.123
16009	7000109	45	75	10	15.6	12.2	8000	10000	0.155
6009	109	45	75	16	21	14.8	8000	10000	0.23
6209	209	45	85	19	31.5	20.5	7000	9000	0.416