Raw material:palm fruits oil processing
Fabrication processing:automatic
Welding:automatic welding
Output:Crude palm oil
Capacity:10-100Ton/hour
Min.Order Quantity:1 Set/Sets
Port:QINGDAO/SHANGHAI/TIANJIN PORT
Packaging Details: Packed by the protect film inner, water-repellent plastic outside. The wood packing is necessary if send by less than a container. sunflower oil etraction factory will fied by steel rope in the container. Make sure it is in good condition when arrived destination.
Delivery Detail:It takes about 50 days to 98 days to finish the complete plant

professional supplier soybean oil expeller machine

Customer visiting

Our factory fabrication ability

Our Certificates

Process specification

1. Fruit peeling and pressing process

Reception station:

A, The FFB bunches will be transported to factory by truck, after be weighted by weighting bridge, the FFB will be

loaded down to FFB Loading Ramp.

B, The iron door of unloading ramp is controlled by hydraulic device, Get the power from Hydraulic pump station.

Starting on the hydraulic device, iron door be lifted. FFB will fall down to the Palm Fruit screw conveyor, and transported

to pre-treatment plant, to Sterilizers.

Sterilizing process:

A, By Scraper Conveyor, FFB be transported to the top of sterilizing tank. Falling into sterilizing tank from feed inlet.

B, Sterilizing tank: The inside diameter of sterilizing tank is 2000mm, length 12500mm, welded up by Q235B

material (Chemical composition:C0.12~0.2%,Si0.12~0.3%,Mm0.3~0.7%,P<0.045%,S<0.045%,Cr<0.3%,Ni<0.3%,

Cu<0.3%).

C, After FFB be transported into sterilizing tank (202), close the door of sterilizing tank, and open the vent valve behind

the tank, then saturated steam, which pressure is 3bar and temperature is about 130

D. After all the cooling air have been discharged out,close vent valve, proceed tosterilizing section. Sterilizing takes

55~60minutes.

E, The time of sterilizing is also according the kind of FFB, if the pressure is too high or the time is too long , palm fruit

will be rot, also Resulting in the loss of oil, high temperature can change palm color.

F, Finish sterilizing process, close the steam valve, open the valve lead to Blow-off/down Silencer, cant open the

sterilizing tank door until discharges out all steam and water.

G, Open the sterilizing tank door, sterilized FFB will fall on the FFB Scraper conveyor. Be transported to net station.

palm oil machine press:

A, The palm fruit is transported to Crush tank by fruit elevator.

B, The fruit in crush tank will be heated to 90~95C, crush time is10~20 minutes.

C, The pounded fruit flow into Palm fruit oil presser to press. Oil press cone can control cylinder,

working pressure is 50~70bar, revolving speed of presser main shaft is 12.5 r/min. Meanwhile the

miture of crude palm oil and water Storage oil tank through crude oil groove. Then oil will be

pumped to Screening filte by oil pump. After filtering take out the oil foam,deposit impurities.

Palm oil flow into Passivating oil tank. The fiber cake and nucleus are ehausted from clearance

of conehead drop on Breaking cake auger.

Weighting---Reception--Sterilizing threshing-----Digesting-----Mashing----Pressing ----Depositing &Purification

----Filtering ----Palm crude oil

2. Palm kernel recycling and pressing process

Pressing cake ----Crushing----Separating fiber&kernel -----Crusher -----Kernel&peel separator ----Kernel dryer

----Drying kernel -----Crushing ----- Pressing

Quality and Service Commitment

Our company always put the interests of customers,product quality and service as first ,and always adhere

to the"no best, only better" as our purpose. We will be commitment to provide high quality products with perfect site services and after-sales service. Now the specific commitments are as follows:

1.Ensure provide complete sets of equipment and accessories timely.

2.Ensure that one-time installation debugging acceptance.

3.To provide high quality material with preferential price.

4.Priority to provide customer our new craftworks and products.

5.Free training technological operator to ensure the trained staff can operation independently.

6.In the installation process,we will appoint an installation supervision staff on the spot.

7.we will offer an eperienced project manager, organize a good installation team for the work.