Specifications

QINGDAO JIAHUA PLASTICS CO., LTD. is the PVB FILM manufacture in China and since then, we are devoting to producing the best quality PVB FILM for you with the good quality PVB RESIN and the 3GO plasticizer. We have passed the ISO 9001:2008 Ceritficate and the TEST REPORT.It occupies the good flexibility, smooth surface and a certain roughness. It is the best gluey material in making laminated safety glass for its well-sticking to inorganic glass until now.

PVB FILM Specifications:

Thickness: 0.38mm     length: 400m     width: 600-2500mm

Thickness: 0.76mm     length: 200m     width: 600-2500mm

Thickness: 1.52mm     length: 100m     width: 600-2500mm

Colored Band PVB Film:

Thickness: 0.76mm Length: 200m;Width: 600-1600mm

Band shade width: 0-380mm

Band Color: blue or green

Technical standards of the laminated glass

1. The glass cutting, cleaning and processing

To begin with, precisely cutting the glass as required is of importance. In case of the bubbles occurred the cutting error must be less than 2mm. Then the well cut glass edge should be grinded and cleaned to remove the oil stains and the other defects. At last, the softened water must be used in the last period to get rid of the unqualified products due to the weak adhesion. After the above process, the clean glass can be dried and placed in the room temperature for future use.        

2. Lamination

In the laminating room, the temperature should be kept in 15~25°C, the humidity 18%~40% , the environment clean and the equipment and employees tidy. The glass must lay flat and so should the film on it. Then lay the other piece of glass on the film. Drawing the film is forbidden during trimming the film. Besides, be assured that the film must be 2-5mm bigger than the glass and the trimming knife keep away from the glass lest the glass particles cause the bubbles on the edge of the laminating glass.                  

3. Pre-pressure exhaust

To get the well sealed edge, the air between the film and the glass needs to be pressed out of the laminated glass. Two methods are generally divided into.

a. Rolling exhaustion.

Firstly, Heat the well laminated glass up to 25~40°C and put it into the first roll (the distance of each rolls are 1mm smaller than the thickness of well laminated glass with the pressure of 0.2~0.5MPa.), then put it into a thermo stated container to heat up to 60~80°C, and then get into the second roll (the distance of each rolls are 2mm smaller than the thickness of well laminated glass with the pressure of 0.3~0.5MPa).After getting out of the rolls, seal the four sides of the laminated glass with clear tape to get rid of the bubbles.

b. Thermo vacuum pre-pressing exhaustion

Put the laminated glass into a vacuum bag or vacuum rubber gasket, and then employ the cool pumping and heat pumping to press the air out. Tips: the decompression vacuum degree is beyond 650mmHg and the cool pumping temperature should be less than 25°C for 30~40 minutes; while in the period of heat pumping, the temperature should be 70~120°C for 30~60 minutes.  

4. Molding in high pressure

Place the Pre-pressure exhausted laminated glasses vertically on glass bracket leaving the distance of each glass more than 5mm. After the glasses are put into the thermo container, sealing the door and raising the temperature to 65°C-85°C; Then raise the temperature and pressure at the same time. The temperature raising rate is controlled in 5°C per minute, and the pressure in 0.06MPa per minute. When the temperature and pressure up to 120~140°C and 1.0~1.5MPa respectively, keep them for 30~60 minutes. After that, keep the pressure and lower the temperature to 45°C, at the same time, loose the pressure to the atmosphere pressure. Finishing the high pressure molding process, we can have the final laminated glass for usage.

 we are glad to have the cooperation with your esteemed company.

Skype: sophie.sun326