Hot Sell Face Muscle Massage Tools Facial Care Machie Microcurrent Important Face-Lfit instrument

Introduction:

Product name: Microcurrent Import Face-Lift Instrument

Model: YSL-800

Voltage: DC9V (1*pp3 9V)

Size: 190*55*35cm

Material: ABS

Vibrating Frequency: 12000 vibrating per minute

Massage method: EMS+ Vibration

Battery information:

To lift the battery, release the clip and open the battery cover. Connect a PP3 9V alkaline battery ensuring the + terminal is as shown. Ensure the MYLAR is underneath the battery and replace cover ensuring it is shut firmly in place.

1 If the unit is left unused for a long period of time, remove the battery.

2 DO NOT use rechargeable batteries.

3 Please ensure that the batteries are disposed of in the correct manner in accordance with local authority requirements.

Programme tips

For best results follow the faradic facial toning regime every day for the first few weeks, alternating between programmes 1 and 2 each day. Afterwards, use as required to maintain good tone.

   To select programme 1, press the programme/on/off button once more. The green light will flash once to indicate programme 1 is selected.

   To select programme 2, press the programme/on/off button once more. The green light will flash twice to indicate programme 2 is selected.

   You will need to adjust the intensity level when treating different areas of the face.

   Press the (+) button 2 seconds, the red light is on to indicate Vibration programme is selected. Then press the (+) button for 2 seconds, the red light is off.

Programme 1- Firming

Rhythmic muscle contractions to condition muscles with a short interval between each pulse. Muscle contractions last 2 seconds followed by a 3 seconds pause. There are 17 power levels in total. We recommend starting on a low power level on each treatment area and build up until muscle contractions are lest.

Programme 2- Tap toning

Rapid stimulating action. The pulsing massage action lasts 5 seconds followed by a 3 seconds pause.

Step 1

Apply a generous amout of conductive gel to each of the ball contacts.

Apply plenty of conductive gel to ensure good contact with the skin.

Step 2

Turn the unit o by pressing the grogramme /on/off button, the light will turn green. The unit will start In programme 1, the programme/on/off button light will flash once.

Step 3

Onto clean skin, position both ball contacts for treating the first area

Step 4

Increase power by pressing the (+) button and move the position of the ball contacts in necessary until you feel definite muscles contractions. If this is uncomfortable, decrease power by pressing the (-) button.

Step 5

Hold the LIFT unit in position for 60 seconds to complete treatment of the area.

After 60 seconds, reduce the power and hold the programme/on/off button for 2 seconds.

Step 6

After use, switch the unit off. Press and hold the programme/on/off button for 2 seconds.

Note: if unit is left on, it will automatically switch off after 10 minutes.

Handy tips

1Start at a low level to begin with until you get used to the sensation.

2.The forehead requires higher intensify levels. Press the (-) button several times before returning to the facial area.

3. Before facial care to firstly ensure that the mask close to the face to make sure that

4.Gently moving the ball to contact in the mask and machine.

Programme 3 –infusion

The infusion programme gives a continuous high frequency sensation. There are 10 power levels. We recommend startmg on a low power level on each treatment area and building up until a strong tingling is left.

Important: For infusion you must remember which ball contact is which polarity. The (+) ball contact should remain on the patch while the (-) ball contact, should remain on the skin.

Step 1

Thoroughly clean and dry skin. Do not apply moisturizers. Tear along the perforated edge of the Collagen and Retinol patch sachet. Take a patch from the plastic casing and peel off the liners to reveal the gel patch.

Step 2

Place one patch onto the area to be treated. Place the other patch on the opposite side of the face.

Step3

Apply a generous amount of conductive gel to the (-) ball contact. Always apply ensure good contact with the skin

Step 4

Select programme 3, infution, by pressing the programme/on/off buttons 3 times, the green light will flash 3 times to indicate programme 3 is selected.

Step 5

With the (-) ball contact touching the skin and the (+) ball remaining on the patch, slowly and gently move back and forth along the patch for 60 seconds. Increase the power until a steady tingling is left.

Step 6

Repeat the process across the other patch. Continue treatment by alternating between patches for 10-30 minutes (5-15 minutes on each patch)

Step 7

The patches may remain on the face for up to 1 hour to continue gently infusion. After removing patches, you can massage any residue into your skin.

Step 8

After use, switch the unit off, press the programme/on/off button for 2 seconds.

Note: if until is left on, it will switch off after 10 minutes.