E-light system

New !!!E-light hair removal beauty equipment,medical laser system port co2 fractional

I.Brief introduction

E-light applies three core technology,IPL,RF,and epidermis cooling ,it combies the advantage of IPL  and RF ,in one hand ,the skin absorbs IPL energy selectively,and the skin also absorbs RF energy ,on the other hand ,the RF -surface-touch cooling technology removing the discomfort and complications by high heat of IPL, therefore ,the effect and safety of E-light makes a breakthrough.

II.System self-checking

The circuit of system entering the self-checking situation when the machine starts ,leave the machine carry on the self-checking for 5-10seconds,then continue the operation .

III.Equipment consist,specification ,and Accessory list.

1.Equipment consist

1>Mainframe

             A.Power supply system

             B.Microcomputer system

             C.Monitor

             D.Cooling system

2>E-light Handpiece

              A.Intense pulsed light source,xenon lamp

             B.Reflector and filter

             C.Sapphire wave guide

2.Technique specification

& Light energy :1-50j/cm2

&RF energy:1-30

&SR spectra:560-1200nm

&Cooling:water+air+semi-conductor

&Spot size:8*40mm

&N.w:50kg

&Dimension:550mm8520mm*1050mm

&Voltage:110V± 10%, 50~60Hz; 230V±10%, 50~60Hz

IIII.Accessory list:

V.Standard treatment process:

1.Form filling

Filling in the blanks of the client file,confirm the treatment program,remind the client pay attention to some points before and after treatment .

2.Face cleaning

    Clean the face with gentle face cream for 3 minutes

     Remind :clean the hands of operator and the handpiece with bromogeramine.

3.Preheating

   Start the equipment after face cleaning ,preheat for not less than 3 minutes(without lighting the xenon lamp)

4.Shaving

     Shave the unwanted hair of the treatment area(2minutes)

5.Gel coating

   Coating the gel evenly (2-3mm)on the skin

    Effect:light guide,cooling ,anaesthetisin.

    Attention :no coating on eyes ,eyebrows,lips

6.Eye protection

    Operator:wear the safety goggles

     Patient:close the eyes,wear professional safety goggles or cover the eyes with eye patch.

7.Allergic test

    Emit2 or 3 light spots in the bottom of ears in safe parameter ,observe for 3 minutes .

    Effect :do not continue to operate if there is a allergic phenomena.

8.Operation

Carry on the operation with a suitable parameter to the operatee

VII.Attention:

1.Inform the operatee that there will be a slight pricking in operation before operating ,to avoid panic.

2.Start the operation with a low energy grade ,adjust the parameters in operating while asking the feeling of the operatee.

3.Move the light spot by one spot overlapping the upper 1/3 part of the previous spot.

 No emitting one area repeatedly ,otherwise may cause inflaming or burns .

4.The handpiece should touch the skin vertically ,no over pressing or leaving the skin .

5.Observing the reaction of skin while operating

6.Cold compress

Keep gel coating for 20minutes after operating ending ,carry out cold compress in obvious slight reddish reaction till reddish fading away.

Cleaning

Clean the gel with cold water ,coat corresponding cosmetics.

Treatment course

Skin rejuvenation program:30-45days/time     4times/course

Hair removal program:2-3months/time          3times/course

2.12  Ask the client before treatment :is there a allergic or not ,its there a bad reaction before for similar operation ,fill the client file concretely ,adjust the parameters on the basis of full acquaintance of the condition of operatee,inform the operatee the possible reation in operation before operating .

2.12.2.In large area treatment or long time continuous operating ,the water inside the equipment will warm up and the handpiece will be not ,interrupt the operation to refresh the water of leave the water cool down to continue operating

2.12.3.Refresh the circulating water in one month,use purified water or medical distilled water .

VIIII.Warranty policy

The warranty of equipment is one year from the date of supply ,during the warranty period ,we undertake to repair free for the equipment supplied against all manufacturing and workmanship defects .

The standard of operation and environment should comply with the product specification and user manual .

The warranty does not extend to any equipment that

a.Malfunctions caused by abused operation .

b.Malfunctions caused by modification or repair by nayone except EASYLASEr or not  authorized by EASYLASER, from which EAYLASER original serial number tag or product identification markings have been altered or removed .

c.Malfuctions caused by other artificial factors like move or tear down in proper motion ,or collision ,etc.

d.Malfunction caused by uncontrollable natural force

e.Energy reduce caused by wet environment and dust

f.Consumable parts of the equipment :handpieces.

We are reliable company in guangzhou ,if you have any questions please contact silin for more detail information and latest price!!!