Name: Q Switched Nd Yag Laser 1064 nm 532nm Q switched nd yag laser
Brand: Nubway
Availability: InStock

Product Details

Q Switched Nd Yag Laser 1064 nm 532nm Q switched nd yag laser

Treatment Principle:

The machine utilizing the explosive effect of the ND: YAG LASER, the laser permeates the epidermis

into the dermis and takes effect on pigment mass and is absorbed by pigment. Since the laser pulses is

extremely short in nanosecond and comes with super high energy, the pigment mass would swell quickly

and break into small pieces, which will be eliminated through metabolism. In this case, the pigments

become lighter gradually and finally disappear.

Technical Parameter:

Laser type	Electro-Optic ND YAG Q-switch laser
Laser output method	Pulse adjusting Q
Working Laser wavelength	1064nm;532nm;1320nm
Laser pulse width	8ns±2ns
Controller	Key press display
Pulse Energy	1800mj(1064nm); 1000mj(532nm)
Power	1300w
Frequency	1~10 Hz
Diameter of spot	0.7~8mm adjustable
Beam of light transmission	7 articular-arm of light guide trasmitting
Indicator of aiming light	Red diode laser
Cooling manner	Closed-off water circulation+air
Net weight	85Kg
Voltage	220V/110V

Treatment Scope:

A. Epidermal pigment: Body Tattoo, Eye line and brow Tattoo
B. Dermal pigmnet: Nevus of Ota, birth mark, Coffe Spot, Age Spot, Freckle
C. Vessels disease: varicosity removal, capillary hemangioma
D. Laser facial: oil control, skin rejuvenation, skin pore improvement

Before & After:

Features:

More Pictures:

Interface

FAQ

1. Can you treat all colours?

No. Light is measured in nanometres and there are two wavelengths of light that are emitted from this

laser C one is invisible infrared light (1064nm) and the other is visible green light (532nm). The infrared

wavelength is preferably absorbed into black and dark blue inks, whereas the green light is absorbed by

red ink. It is possible to treat some other colours although white, yellow and bright colours are difficult.

This is not usually a problem however, as lighter colours cover very easily. If you wish to cover-up an

existing tattoo then the darker colours will be faded or removed, allowing you greater choice of size and

colour of the cover- up design you choose.

2. Will the tattoo be removed in one treatment?

No, that is very unlikely. The light can only shatter a certain amount ink in one treatment, so several

treatments are needed at 4-6 weekly intervals to work through the layers. You will notice the tattoo fades

more and more with every treatment you have. A test patch will be performed before a full session goes

ahead to check how you react to the treatment. A professional tattoo can take between 4 C 5 treatments

and sometimes only take 1 or 2. There are several factors that influence the number of treatments required,

these can be down to how easily you heal, how deep the ink is in the skin, and the types of ink that were

used. Generally speaking the longer you have had the tattoo and the darker it is, the easier it is to remove.

3. What happens to my skin after treatment?

The immediate after effect of the treatment is that the skin turns temporarily white, this is due to water

evaporation and disappears with an hour or two. The skin also swells and feels like mild sunburn, this

usually disappears within 24-48 hours. It may blister too. The body continues to remove ink after the

treatment and the skin is usually back to normal within a few days.

4. Are there any side affects?

Sometimes if you use too high energy, bleeding and/or blistering can occur. Especially for lady's skin, very

weak. So you just need to use the energy that can make the tattoos become white, begin from our original

energy.

5. Will the laser treatment scarmy skin?

No. If bleeding or blistering does occur it is very important not to pick any scabs that may result when the

skin is healing C this could cause scarring, and should be avoided as scar tissue can make further treatments

more difficult.

Our Services

1.3 years warranty, if there any problem happens with your machine, we will repair it free

of charge (except the intended damage)

2.Convenient training, user manual and operation video are available, also, if it is not

enough, we can provide the online face to face traning

3.OEM/ODM services, your logo, outshape, language, interface can specially be designed

on your machine

CE certificate