co2 fractional laser resurfacing

Specifications

1, USA COHERENT laser device 
2, 40w strong power 
3,0.1mm Dot interval  
4. Wrinkle removal

5. Pigmented acne scar removal 

6.gynecology treatment , vaginal renew

7.German Graphics Generator

1.laser co2 fractional The scope of treatment:

Fractional CO2 Laser Vaginal Tightening

1.Fractional function,2.Skin Rejuvenation3.Skin Tightening, Aging Skin Treatment4.Collagen

Stimulation5.Smooth out wrinkles and fine lines6.Flatten worry and frown lines7.Clearing sun-

damaged skin8.Shrinking the appearance of pores9.Remove age/sun spots on the skin10.Acne

and acne scar removal11.Remove intractable chloasmas and pigmentation;12.Eliminate striae gravidarum13.Rejuvenate your neck, chest and hands etc.14.Flatten traumatic scars

2.Cutting function (this only can be operated by professional doctors)

1.Smooth burnt scars and surgery scars, dermabrasion, etc.2.Actinic keratosis3.Basal cell

carcinoma4.Laser skin resurfacing5.Eliminate the scar: Traumatism, operation, Burn debridement,

Cosmetic surgery,6.Decrease jowls and improve angle of the jaw7.Reshape, slightly enlarge,

and give firmness to lips8.Remove mole, verrucous, and small tumors of the skin9.Hemangioma lesions10.Blepharoplasty 

3.Vagina renew treatment :

 certificate

A numbing cream is applied to the area for at least 1-2 hours prior to treatment, and in some

cases local an aesthetic injections are used. Pain puffers and medication can also be used if needed.

The laser is applied to the affected areas. At the end of the treatment the area will look like small

white  or red dots that disappear by the following day. There is usually redness that lasts at least 7 days,

and swelling for a few days. Most people need  about 5 days off work.

How many treatments will I need?
Depending on the degree or wrinkling or scarring and your expectations, you would usually

need 1-3 treatments. Some people need more, especially those with severe acne scarring.

What do I look like after the treatment with Fraco2?
Immediately after the treatment you will look red, with tiny white dots, or pinpoint bleeding on your skin.

These dots usually disappear the next day. Swelling will last a few days and redness at least 7 days.

You can apply makeup usually after 3 days, but you  usually need a few days (5-7) days off work.

What precautions do I need before the treatment?

There are no special precautions before the treatment except:

1.If you have a history of cold sores, you may need to take an anti cold sore tablet starting

the day before treatment.

2.If you have recently taken Ro Accutane for acne, you may more suited to non ablative

fractional laser, eg,

What do I do after the treatment?
After the treatment, in most cases you will

1.Take antibiotics to prevent infection (depending on the doctor’s decision)

2.Use light non greasy moisturizer and sunscreen, the clinic will recommend one that is suitable for your skin.

3.You may wish to take anti swelling tablets for a few days.

4.You may wish to use compresses with white vinegar and water for the first 24 hours to reduce swelling.

5.Apply makeup after the a few days.

6.Wash your skin with a gentle cleanser eg Cetaphil lotion.

7.If you have darker skin, you may need to use a bleaching lotion after the treatment  to prevent

post treatment increase in skin pigmentation.

What sort of result can I realistically expect?
After one treatment session, depending on the strength of the treatment, you should notice a

significant improvement in wrinkles especially around the eyes. Lines around the mouth are more

difficult and may need more than one session.
Acne scars usually show more improvement with the fractionated CO2 laser than with the older

laser after the first treatment.

1. 3 years warranty with lifetime free service and maintenance

2. Free training for operation of the equipment in our company, which provided by our specialized

training department.

3. On-line services, for example, technical consultancies provided by our skilled technique group

concerning any question of the laser equipment, and after-sale maintenance and more.

4. OEM/ODM services are available. We have our own developing and design department and

manufacturing line, which ensure your required beauty equipment

5. Professional after-sale service team, solve all the problems in time