Salon Use Diamond Peeling Skin Care Microdermabrasion Beauty Instrument
USD $1 - $110 /Set
Min.Order:1 Set
Guangzhou Holy Beauty Equipment Co., Ltd.
Salon Use Diamond Peeling Skin Care Microdermabrasion Beauty Instrument
Main Function:
* Rejuvenation of sun damaged skin - face, neck, shoulders, back, arms and legs
* Reduction of age spots.
* Minimization of blotchy skin coloring.
* Reduction of acne and superficial scars from past injury.
* Extraction of blackheads and whiteheads.
* Reduction of oily Skin.
* Improvement of overall skin health
What is Diamond Microdermabrasion:
provides a non-surgical skin refinish procedure, by using sterile diamond heads to abrade or rub off the top skin layer, then vacuuming out the particles along with any dirt and dead skin backup. This procedure removes skin debris, imperfections,blemishes, wrinkles and unwanted pigmentation on the skin. Moderate usage of Diamond Microdermabrasion, accompanied with skin products that penetrate through the top skin layer that reach the dermis level, helps to replenish natural nutrients, restore cell activity, and promote skin health. The results after a Diamond Microdermabrasion treatment are healthy, glowing,beautiful skin.
Tips size including :
D120,D180-Body,especially for acne,knee,elbow areas and striae of pregnancy.
D180,D240-face,for the large blemishes.
D120,D240, D180 -for scares,fine lines and imperfections.
D200-Eyes and both sides of nose,for wrinkle,oil tablets,blackhead and acne.
D240-Eyes and both sides of nose.For wrinkles,oil teblets,blackheads and acne.
Operating Instruction for Diamond Dermabrasion
1. Push in the movable ring of copper nozzle at the hand piece, and pull out the 6x4 size vacuum hose. Then push in the black plastic ring on the vacuum hose.
2. Put a drop of cream or milk lotion on the vacuum hose nozzle, push in the movable ring and insert in the vacuum hose to the limit.
3. Insert a cotton swab into the Diamond Head, then tight up the Diamond Head on the hand piece. Remove the cotton swab after every treatment.
4. Turn on the power switch.
5. Adjust the Vacuum intensity by Vacuum Regulator according to the following reference table, the intensity displays on Vacuum gauge and check with the client for comfort.
6 Use the incline area of Hand piece to contact with the skin surface. Proceed with a slow sliding motion. Do not place the hand piece at one spot for too long, doing so will cause harm to the skin.
7. Adjust the crystal flow rate by the Vacuum Regulator slowly from minimum to maximum. For commonly use, do not set the flow rate to maximum unless it is of necessity. This is for bettercomfort intensity.
8. Gently stretch the skin with thumb and finger and glide the Hand-piece 2 to 3 times over the area being treated. Then cross again in different directions to prevent streaking lines as in the reference picture. Brush strokes or polishing motions may be used in different sites.
Recommended Vacuum intensity on treatment area
Treatment Area | Normal Skin (inHg)vacuum intensity | Sensitive Skin (inHg) vacuum intensity |
Face | 12-22 | 8-12 |
Forehead | 12-22 | 10-12 |
Chest | 15-20 | 15-18 |
Nose | 10-15 | 10-14 |
Neck | 18 | 10-15 |
Near eye area | 8-12 | 8-10 |
Treatment Schedule Table
Treatment | Frequency (days) | Total Visits |
Face Peeling | 6-10 | 3-5 |
Fine Lines | 7-13 | 6-8 |
Neck | 12-14 | 3-5 |
Acne Scars | 7-12 | 8-10 |
Hyperpigmentation | 7-12 | 8-10 |