1 Product Presentation
TND/TNS series automatic AC voltage regulator is composed of the contact voltage regulator and automatic control circuit. The voltage signals are sampled and amplified to control the servo motor to drive the rotating arm and the electric brush to rotate in the desired direction so that the output voltage can be adjusted to the rated value to achieve the purpose of stabilizing the voltage. Performance indicators fully meet the Q/ZT 78 standard.
The voltage stabilizer has the advantages of beautiful appearance, small size, light weight, low power consumption, complete protection function, stable and reliable, and low output waveform distortion. Can be widely used in industrial production, scientific research, medical and health, household appliances, such as power grid voltage fluctuations or large power grid voltage seasonal changes in the region, can provide high-quality power supply to any load.
Meet the standards: JB/T 10089, Q/ZT 78.
2 Working Environment
2.1 ambient temperature: -5℃- +40℃.
2.2 relative humidity: no more than 90% (temperature is +20℃).
2.3 the installation location of the altitude is not more than 2000m.
2.4 installation: the installation environment should be well ventilated, no obvious pollution, corrosive gases, dust, flammable and combustible gas.
3 Technical Parameter
Input Voltage Range | 150-250V(Other regulated range can be customized) |
Output Voltage | 220V(Other voltages can be customized) |
Output Accuracy | ±3% |
Working Frequency | 50/60Hz |
Display | Analog Meter (LED or LCD is optional) |
Efficiency | ≥98% |
Ambient Temperature | -10 to +40°C |
Altitude | ≤1000m |
Relative Humidity | ≤90% |
Insulation Resistance | ≥5MΩ |
Waveform Distortion | No |
Protection Function | Under voltage, over voltage, short circuit, phase missing (single phase have no) |
Response Time | <1s (input voltage varies within ±10%) |
Load Power Factor | 0.6-0.8(Depending on the type of load) |
Regulation Type | Servo motor type |
Transformer Type | Toroidal Autotransformer |
Protection Level | IP20 (Optional: IP44, IP54, etc) |
| 4 Structural Characteristics The output capacity of the product is closely related to the input voltage. The output capacity curve is shown in Figure(1). When the input phase voltage is lower than 198V (three phase line voltage 342V) the rated output capacity of the product will be reduced; When the output voltage is selected as 110V the output capacity is only 50% of the nominal capacity; |
|
5 Ordering Instructions
For your safety, please read the following selection requirements and precautions when ordering:
5.1 this series of three-phase product input and output for three-phase four wire system connection, so the use must be used to meet the zero line;
5.2 three-phase stabilized voltage power supply in single-phase application or three-phase applications, each phase output maximum capacity of 1/3 of the nominal capacity of the machine.
5.3 under normal circumstances in the selection of power equipment rated power, power surge current, inductive or capacitive load conditions to choose a reasonable voltage regulator
Power supply, the output capacity should be left to a sufficient margin, especially the impact of load type selection margin to be greater, the specific type of safety factor table (1)
Load property | Equipment type | Safety factor | Capacity of voltage regulator |
Pure resistive load | Incandescent lamp, electric | 1.1-1.3 | ≥1.1-1.3 times the total load power |
Inductive and capacitive load | Fluorescent lamp, fan, water pump, air conditioner, refrigerator, etc. | 2.5-3 | ≥2.5-3 times the total load power |
Table (1)
5.4 when the input voltage is lower than 198V, the output capacity of the regulator has declined, so to reduce the load drop to avoid overload, the specific characteristics of figure(1);
When using the 220V output or the use of the same time, the maximum total output current shall not exceed the rated output current, using the maximum capacity of 110V output is only half of the rated capacity;
When the input voltage is lower than 198V, it should be used in reference to figure (1) curve, so as to avoid overload.
6 Our Services
6.1 inquiries / technical consulting / service will be returned within 10 minutes of the working day.
6.2 the best quality; reasonable price; accurate time; timely and effective service.
6.3 OEM/ODM services, we can put your company name or logo printed on the product and packaging, but you should give us a trademark license.
6.4 all of our products have two years of warranty, we can provide services for more than 2 years of warranty products, of course, you need to pay the cost of the corresponding.