Name: wall mount 12v 1.5a 18w eu plug led transformer
Brand: SMARTS
Availability: InStock

Product Details

wall mount 12v 1.5a 18w eu plug led transformer

Product Description

1.Specification:

model	output voltage	Current	power	Tol.	R&N	Effi.
SMT-012-018VP	12V	1.50A	18W	±3%	80mV	>82%
SMT-024-018VP	24V	0.75A	18W	±2%	180mV	>82%

2. INPUT REQUIREMENTS:

2.1 Operating range: 90-264VAC

2.2 Rated Input Voltage :100-240VAC

2.3 Input Frequency Range: 50/60Hz +/-3Hz

2.4 Input Current: 0.2A max

3.OUTPUT REQUIREMENTS:

3.1 Output Voltage and Current

Output	Output Regulation(V)		Harf Load	Rating Load (A)
Voltage(V)	Minimum	Maximum	Current(A)	Continuous Current(A)
12V	11.4V	12.6V	0A	1.5A

3.2 Output Voltage Regulation

The total output voltage regulation shall be +/-5%,including the effects of line voltage variations,load current,ripple and noise,and the AC component of the load current.

3.3 Output Voltage Ripple

The switching power supply shall not exceed the following limits in the indicated voltage for 60Hz or 50Hz ripple,switching frequency ripple and noise measured with 20MHz width.

Ripple and Noise:50/60Hz Ripple + Switching Ripple and Noise

Output	Ripple
0-1.5A	200mV

Ripple and Noise are measured at the end of output cables which are added a

0.1uF(104) Ceramic capacitor and a 22uF Electrolytic capacitor.

4. EFFICIENCY:

When 230VAC line input voltage (100-240 VAC),the efficiency shall be >79% at rating load.

5. DIELECTRIC STRENGTH (Hi-Pot) TEST:

Finished product withstands with AC 3000Vrms/50Hz,5mA max,

primary to secondary, 1 minute for type test,1 second for production test.

6. INSULATION RESISTANCE:

Primary to secondary: 10MΩ min at 500VDC.

7. PROTECTION:

7.1 Short Circuit Protection

If short circuit occurs,all the output should be protected. After the fault, the adapter automatically recovers.

7.2 Over Shoot

The Output over shoot at turn-on shall not exceed 10% of normal voltage value with or without the load connected.

7.3 Start-up time

The start-up time is less than 2 second.

8.ENVIRONMENTAL CONDITIONS:

8.1 Temperature

Operating temperature: 0℃ to +40℃

Storage temperature : -20℃ to +60℃

8.2 Humidity

Relative humidity:≤95%

8.3 Operating Ambient Altitude

Altitude:0-3000m

8.4 Operating at the lower temperature

At -0℃,with the rated voltage 100-240Vac charged to the primary and unloaded and full load on the secondary 8 hours, no abnormality in electric and mechanical characteristic, after 2 hours recovery at the room temperature.

8.5 Operating at the high temperature

At +40℃,with the rated voltage 100-240Vac charged to the primary and unloaded and full Load on the secondary 8 hours, no abnormality in electric and mechanical characteristic, after 2 hours recovery at the room temperature.

9. COOLING:

Cooling shall be with natural convection cooling.

10.Burn-in

The burn-in test will be performed at least 4 hours at centigrade

degrees under full load Condition.

11.Referenced standard:

11.1 EMI Standards

Reference EN50082-1,EN55022-B,GB-17625.1-2003, GB-9254-1998

11.2 Safety Standards

The adapter shall be meet certified with the following safety standards.

UL60950-1,EN60950-1,GB4943-2001

12. MOUNTING CONNECTORS:

12.1 AC Input Connector

Spec :2Pin (CE PIN)

12.2 DC Output Cable

Wire : (Optional) 24AWG*2C L=1200mm Color: Black

Plug : (Optional) 5.5 x 2.1x 10mm Turning fork line

13. MECHANICAL FEATURES:

13.1 Dimension(Size)

Length: 59.8mm

Width: 38.8mm

Height: 45mm

13.2 Weight

The Power Supply unit : 65±10g

13.3 Vibration and shock

No Evidence of any mechanical or functional damage after the vibration and shock testing.

Test conditions		Acceptance Criteria
Frequency	10-55Hz	Nominal functional test should be satisfied after the test
Sweep	For each axis(X,Y,Z)
Displacement	0.15mm
Periodicity	10

13.4 Drop test

After Dropping from a hight of 100 cm onto a wooden floor , Dropping at 6 sides totally, NO breakage should be happened in the test piece.

13.5 Bending Test

Fix the power supply and its plug, apply a load of 200g to the other end, turn the cable by +/-60℃ carry out this process 1000 times, at the rate of 20 times per minutes. No abnormality in mechanical and electrical Characteristic and disconnection within 30% after the test.