Specifications

The reliable functions, portability and application flexibility of A80 are all in the international leading positions.

The functions:

• Built-in touch screen industrial PC
• Multi-detector for selection
• Split system with micro-packed column
• Vacuum negative pressures for ample injection
• Automatic selection module of many sample flow paths
• Design of Explosion-proof armor heating
• Integration module design with multi-column and multi-valve
• Sweep protection and leak-tightness automatic sample injection diaphragm valve

A80 Main technical Parameter

• Structural composition

Column box:4 separated electrical heating Column box, working temperature:ambient~350°C Temperature controlling precision: ±0.1°C

Detector: TCD, FID, HID, ECD, PID. working temperature: ambient~350°C

Sampling/ Column cut valve: membrane valve, rolling piston valve, High temperature high Pressure valve, blow through valve Corrosion resistant valve

Chromatographic column: 1/16 1/8packed column, capillary column

EFC: Though max 9 access EFC

• Performance

Measuring scope: TCD: 5ppm~100%, FID: 0.1ppm~100%, HID: ppb~100ppm,

                              ECD: 0.01ppt~10ppm, PID: 0.1ppb~1000ppm

Repeatability: ±3%RSD

Analytical period: 5 seconds~3hours

• Communication function

LAN TCP:/IP Agreement port open

USB2.0

RS232

• Gas sampling requirements

Sample flow: 10~100ml/min

Sample filter: 2μ

Min pressure: 3~5psi lower pressure can be chosen

Max pressure: 75psi Higher pressure can be chosen

Highest sample temperature standard: 100°C, higher temperature can be chosen

Sampling tube material: Teflon tube, Stainless steel tube, polyimide tube Other materials can be chosen

• Standardization

Mode: manual or automatic

Null point: automatic baseline revise

Measuring scope: steel cylinder Regulator

Quickly on-site logging analysis

One machine with double functions: 25 sec isolates C₁~C₅, 115 sec isolates C₁~C₈

All intelligent control, automatic ignition, automatic null point Calibration, automatic fault diagnosis

Measuring scope: component 5*10 ^-6-100%, total hydrocarbon: 10^-5-100%

Natural chromatographic analysis

Separation for many valves and columns, TCD system analysis H₂, O₂, CH₄, CO, C₂H₆, CO₂, H₂S, C₂H₄, C₃H₈, C₃H₆, C₄, C₅, C6+ and ect.

Analytical process

The analytical system consists of a ten connection valve, two 6-way valve, four Chromatographic column and one thermal conductivity detector.

The flow diagram lies in original state, when put the sample into No. 9 mouth of valve V1 into quantitative tube 1, after sweeping clean, switch V1 from OFF to ON, carrier gas 1 takes sample into analytical column DC200, before components flowing out, switch valve 1 from OFF to ON, C₆+ was flow back to TCD, examined.

Components O₂, N₂, CH₄, CO, CO₂ and C₂ flow out from DC200 and flow into chromatographic column PQ, and when components H₂S, C₃ and above have not flowed out, switch the valve V2 from OFF to ON. Then H₂S, C₃ and above will be brought into detector TCD by gas carrier 2 and be detected, switch the valve V2 from ON to OFF. Before CO₂ and C₂ flowing out, O₂, N₂, CH₄, CO flow into chromatographic column 13X, switch the valve V3 from OFF to ON. Components CO₂ and C₂ will be detected by TCD in sequence. Switch the valve V3 from ON to OFF, components O₂, N₂, CH₄ and CO will be detected. Analysis process finish.