Specifications

Ferro-magnetic Neon Transformers
The models available are 15KV, 10KV and 7.5KV with current capacity of 30mA.

UL Listed T30 Series Ferro-magnetic Neon Transformers

 

1) Features 

Neon Transformers are magnetic transformers suitable for Neon Lighting. The models available are 15KV, 10KV and 7.5KV with current capacity of 30mA. Typical features in these transformers are 

1. On/ Off switch (optional on request) 

2. Fuse 

3. Surge protection

4. LED indicators and fault detection

5. Epoxy molded inside

6. Good for Interior or Exterior use

7. Heavy duty metal body

 

The T30 features:

* Complies with secondary Ground-Fault Protection requirements in UL2161 and CSA C22.2 NO.255

* Service mode deactivates Secondary Ground-Fault Protection for 10 minutes.

* Unit does not work without proper ground. 

* Exceed and insufficient input voltage protection.

* Secondary-circuit open and overload protection.

   

2) Specification 

NEON TRANSFORMER WITH UL2161 COMPLIANT SERVICE SWITCH                          

To activate service mode: while the transformer is on, depress and hold the switch for 1 second and release. The tubing will flash on 3 times to indicate the transformer is in service mode (SGFP circuit is disabled). The tubing should then remain on. The tube may not light if the tube is broken or shorted. The green LED will constantly flash while unit is in service mode. The unit remains in service mode for 10 minutes. After 10 minutes, the unit will return to normal mode. To escape service mode before the 10 minutes has elapsed, depress the service switch an hold for 1 second and release, or turn power off, wait for 3 seconds, then turn power on. The unit will restart in normal mode.        

                    

Models	Input		Output
	Voltage (V)	Current(A)	Voltage(KV)	Current(mA)
T30-150	120V AC/60Hz	3.90	15	30
T30-120	120V AC/60Hz	3.40	12	30
T30-090	120V AC/60Hz	2.80	9	30
T30-075	120V AC/60Hz	2.30	7.5	30

 

The loaded lamp (tube) length can be adjusted to the maximum value listed below:

Items   Models	Tube Diameter (mm)	18	15	14	13	12	11	10	9
	Gas Pressure (mmHg)	8	9	10	10	11	12	13	15
	Tube Type	Maximum Load Length (ft)
T30-150	Neon	72	60	54	50	45	40	36	32
	Mercury	80	72	64	60	54	48	44	39
T30-120	Neon	55	45	42	39	35	32	29	26
	Mercury	62	55	50	46	42	38	35	31
T30-090	Neon	40	33	30	29	26	24	21	18
	Mercury	45	40	36	33	31	26	25	22
T30-075	Neon	28	26	24	22	21	19	17	15
	Mercury	35	31	28	27	25	23	20	18

 

Remark:

The maximum length in feet may vary according to output cable length and environment. Deduct one foot from above figures for each pair of electrodes while more than two tubes connected in series. Figures for mercury tubes are based on operation in temperature above 4℃. Deduct 25% value of above if operation below 4℃. Do not operate over the maximum value, otherwise the lifetime and performance of this device may be reduced.

 

 Neon Transformer Installation Guide

DANGER!         HIGH VOLTAGE

l   Remove primary power before serving the sign or transformer in any way.

l   Secondary Ground-Fault Protected (SGFP) transformers will NOT provide protection against electrical shock. Potentially hazardous high voltage can be present.

l   Service and/or installation should only be performed by qualified personnel.

l   Do not assume power is removed from transformer if ground fault trip occurs (the transformer will automatically make 3 attempts within approximately 10 seconds to reset.)

l   Installation must be in total compliance with the National Electrical Code, the requirements of Underwriters Laboratories and applicable local codes.

l   Failure to properly ground this transformer may result in the transformer case and any metal connected to it to become electrified if a secondary ground fault exists. The transformer should have a good ground.

 

A good ground is:

a) An approved and properly sized grounding wire that can be traced all the way back to breaker panel.

b) Metallic conduit terminated in fittings listed for grounding all the way back to its breaker panel.

 

                                                                                                                                                                             

INSTALLING the Neon Transformers (see installation diagrams in page 1):

1. Securely mount the transformer in an approved metallic enclosure.
2. Run the service wires through conduit into approver enclosure.
3. Connect the line service wire to the identified positive terminal. Connect the neutral service wire to the identified negative terminal. Insure the line and neutral service wires are connected properly and are not reversed.
4. Bond the service grounding wire to the sign enclosure per UL48 and the National Electrical Code. Electrically connect another wire to this same service ground connection or to a terminal secured to a grounded part of the sign enclosure. Connect the free end of this wire to the identified service ground (“G”) terminal on the transformer.
5. Improper grounding can result in electrifying all metal connected to the transformer during a secondary ground fault condition.
6. Run GTO wires from the first neon tubing electrodes through separate conduit, raceway, sign body, etc. to each transformer secondary high voltage bushing. (These wires should be kept as short as possible, but may not exceed 20 feet.)
7. Make sure to securely tighten all service and high voltage output terminal nuts.
8. Replace transformer can box cover if applicable.

3) Photos 

 

  

5) Workshop

 

 

6) Certificate 

 

 

7) WARRANTY PROCEDURE

The YIYA Warranty Policy as stated in our catalog is as follows: YIYA, a Chinese manufacturer, warrants to the original purchaser the products described herein to be free from defects in material and workmanship at the date of shipment.  

 

NO OTHER WARRANTY, WHETHER EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL EXIST IN CONNECTION WITH THE SALE OR USE OF SUCH PRODUCTS.  

 

All claims under this warranty must be made in writing and delivered to the Company prior to the expiration of two years from the date of manufacture or one year of operation, whichever should occur first. Upon receipt of claim, the Company shall inspect the part or parts claimed to be defective, and the Company shall repair, or at its option, replace, free of charge, any part or parts which the Company determines to have been defective at the time of shipment from the factory; provided, however, that if circumstances are such as to preclude the remedying of warranted defects by repair or replacement, the Company shall, upon return of the products, refund to buyer any part of the purchase price of the products. Theretofore paid to the Company. Inspection shall, at Company’s option, be performed at the Company’s plant, or at such other place as may be designated by Company, and in such event freight for returning products to Company’s plant or to such other designated place shall be paid by buyer.  

 

The foregoing states the sole and exclusive remedy for any breach of warranty or for any other claim based on any defect in, or non-performance of, the products, whether sounding in contract, warranty, or negligence.   

 

WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, THE COMPANY SHALL UNDER NO CIRCUMSTANCES BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGE WHATSOEVER ARISING OUT OF, OR IN ANY WAY RELATING TO, ANY SUCH BREACH OF WARRANTY OR CLAIMED DEFECT IN, OR NON-PERFORMANCE OF, THE PRODUCTS.  

 

2 YEARS 

NT Neon ferro-magnetic Neon Transformer (Indoor & Outdoor) 

TH5-NT Neon ferro-magnetic Neon Transformer 

T30 Neon Ferro-magnetic Neon Transformer  

Cold Cathode Transformers  

 

1 YEARS 

NEON ACCESSORIES (Electrode, End Cap, Light Supports, Neon Tester, Neon Tube, Silicone Cable, ,,) 

NEON VACCUM SYSTEM 

BOMBARDER TRANSFROMER 

ALL OTHER COMMIDITY MADE IN YIYA. 

  

NOTE: Warranty credit will not be given for units that have been altered in the field or show evidence of misuse.  

 

Why Choose Us?

 

Original SINOLITE/YIYA brand 

  1. We sell 100% original real SINOLITE/YIYA brand, and  have the certificate of UL, CUL, CE, CB, RoHS etc.

   2.The different S/N code on surface of the products, can check the code with SINOLITE company.  

 

Competitive Price +A Fast Delivery + Satisfied Customer Service 

  1.Our goal is to provide you the right product and make you satisfied, so please don’t hesitate to contact us via Tel or mail. 

  2. We shall find for you the cheapest shipping term and show you the freight and shipping time. Regarding to the urgent order, a quickest shipping term and freight will be advised to you for consideration. 

  3.The stock info will be informed before your order, to make everything under control. 

  4.We will quote to you competitive prices according to your quantities. 

  5.Price could be negotiated for more and large quantity. 

  6.We have a technical team, if you show us your Neon Power Supply information, we can find right device for you to match neon sign.  

 

Shipping & Duties 

Usually, shipping will be arranged within 2-3 Days upon payment or deposit, from Monday to Saturday only.  

 

Payment 

To assure you the maximum comfort and satisfaction, Currently, you can pay via T/T, L/C, WESTERN UNION, PAYPAL, More payment options will be added in the near future.  

 

After-sale service 

All of the products we sell are with a certain time warranty. 

during the warranty, anything wrong with it, like no working an unstable output voltage or current, damaged, my corporation will be responsible to fix it well for free and re-send it to the clients, But, the delivery cost should be paid by purchaser himself. 

We will be very glad to provide the assistance during your installation and application at any time. 

 

Contact Us 

Your inquiry and mail will be quickly responded. Suppose you have no ideas on choosing the right power supply, please do not hesitate to contact us.

 

Shanghai Jiabao Trade & Development Co., Ltd. 

Add: 2551 Dachuan Road, Nanhui Industry Park, Pudong New District, Shanghai, 201399 P.R.China 

Tel: 0086-21-58180613 

Fax: 0086-21-68014262 

Website:   

Skype: sinolift 

Contact person: Mr. Irving Deng  

Cell No.: 0086-13817572420