MOS-620CT,Analog Oscilloscope 20MHz Bandwidth
Negotiable /Piece
Min.Order:1 Piece
Xiamen Wellzion Electronics Co., Ltd.
Model | MOS-620CT | MOS-640CT | MOS-650CT |
Vertical Axis | |||
Frequency bandwidth | DC~20MHz | DC~40MHz | DC~50MHz |
Rise time | Approx.17.5ns | Approx.8.75ns | Approx.7ns |
Sensitivity | 5mV~5V/DIV,10 steps in 1-2-5 sequence | ||
Vernier Vertical sensitivity | To l/2.5 o r less of panel-indicated value. | ||
AC coupling | Low limit frequency10Hz. (With reference to 100KHz, 8DIV. Frequency responsewith-3dB.) | ||
Input impedance | Approx . lMohm //Approx.25pF | ||
Linear ity | Adjustable on panel | ||
Vertical modes | ≤± 0.l DIV of amplitude change when waveform of 2 DIV at graticule center is moved vertically. | ||
DC balance shift | CHI :CHl single channel. CH2 :CH2 single channel. DUAL :CHI and CH2 are displayed. ALT or CHOP selectable at any sweep rate. ADD:CH1+CH2 algebraic addition. | ||
Chopping repetition frequency | Approx.250kHz | ||
Input coupling | AC, GND, DC | ||
Maximum input voltage | 400V (DC+AC peak),AC:freq uency lkHz or lower. | ||
Common mode rejection ratio | 50:1 or better at 50KHz sinusoidal wave(When sensitivities of Ch1 and Ch2 are set equally) | ||
Isolation between channels (At 5mV/DIV range) | >1000:1 at 50KHz | ||
>30:1 at 15MHz | >30:1 at 35MHz | >30:1 at 45MHz | |
CH2 INV BAL | Balanced point variation:≤1DIV (Reference at center graticule) | ||
Triggering | |||
Triggering source | CH1,CH2,LINE,EXT,ALT | ||
Coupling: AC | 20Hz to full bandwidth | ||
SLOPE | +/- | ||
Sensitivity | 20Hz~2MHz:0.5DIV, TRIG-ALT:2 DIV, EXT:200mV | ||
2~20MHz:1.5 DIV | 2~40MHz:2.5 DIV | 2~50MHz:3.0 DIV | |
TRIG-ALT:3DIV, EXT:800mV; TV: Sync pulse more than 1 div(EXT:l V) | |||
Triggering modes | AUTO,NORM,TV-V,TV-H | ||
EXT triggering signal input Input impedance Max.input voltage | Approx:1MΩ/approx.25pF; 400V (DC+AC peak), AC: Frequency not higher than 1KHz | ||
Horizontal System | |||
Sweep time | 0.2uSec~0.5Sec/DIV,20steps in 1-2-5 sequence | ||
Sweep time accuracy | ±3% | ||
Vernier sweep time control | ≤1/2.5 of panel-indicated value | ||
Sweep magnification | 10 times | ||
×10MAG sweep time accuracy | ±5% (20nSec~50nSec are uncalibrated) | ||
Linearity | ±5%, xl0MAG:±10%(0.2s and1 s ) | ||
Position shift caused by ×10MAG | within 2DIV. At CRT screen center | ||
X-Y Mode | |||
Frequency bandwidth | DC to at least 500KHz | ||
X-Y phase difference | ≤3°at DC~50KHz | ||
Sensitivity | Same as vertical axis. (X-axis:CH1 input signal; Y-axis:CH2 input signal.) | ||
Calibration Voltage | |||
Waveform | Positive-going square wave | ||
Frequency | Approx. 1kHz | ||
Duty ratio | Within 48:52 | ||
Output voltage | 2Vp-p±2% | ||
Output impedance | Approx.1KΩ | ||
CRT | |||
Type | 6-inch rectangular type, internal graticule | ||
Phosphor | P31 | ||
Acceleration voltage | Approx.2KV(20MHz)/Approx.12kv(40MHz) | ||
Effective screen size | 8×10DIV[1DIV=10mm(0.39in)] | ||
Graticule | Internal | ||
Trace rotation | Provided | ||
Dimensions | 310W x150Hx 455 D(mm) | ||
Weight | Approx.8kg |