Name: CE Certificated Modular Construction Rapid temperature change chamber for pcb
Brand: kOMEG
Availability: InStock

Product Details

CE Certificated Modular Construction Rapid temperature change chamber for pcb

ESS traditionally increases product reliability four times that of unscreened electronics.

What is ESS?

Environmental Stress Screening (ESS) is a means of screening electronic assemblies at the most cost-effective point of manufacture to expose defects that can't be detected by visual inspection or electrical testing. These defects are typically related to defective parts or workmanship and are normally found as early field failures.

1. Explore Temperature Chambers by KOMEG Different Series:

KMT-R Series, KMT-L Series, KMT-S Series

Simulate high and low temperature environments in Associated Environmental Systems bench top or floor model temperature chambers.

1) Working volume from 64 to 1000 cubic L.

2) Conform to commercial and military standards for high and low temperature tests.

3) Self-contained single-stage refrigeration systems support low temperatures to -158°F / -70°C.

4) Two-stage cascade refrigeration systems support low temperatures to -140°F/-60°C. The two separate closed refrigerant circuits each use a different refrigerant with its own compressor.

2. High temperature limits of test chambers

There are many types of test chambers, but they all high and low temperature limits. Let's take a look at the typical high temperatures thresholds and why they exist.

Test chambers usually have wire heaters made of a material called Nichrome. By placing successive loops of heater wire, a greater amount of heat that is generated. The result looks a lot like the inside of a toaster. Fans circulate the air past the heaters, so the samples in the chamber are not exposed to radiant heat. It is very easy to add heaters and increase the speed and / or high limit of a chamber.

KOMEG chambers typically have a high temperature limits under 200°C. Here is a break-down of why a chamber's high temperature limit exists:

150°C: There are two reasons we may limit a chamber to 150°C. First, there may be a limitation of the materials used inside the chamber. Secondly, for extremely fast chambers, we may limit the high temperature to avoid problems with accidentally tripping overheat protection devices.

170-180°C: Most models stop at this temperature range. There is a risk of burning the oil inside the refrigeration's cooling coil.

3. Parameter Specifications:

Model	ESS-SL
Model	1000SL15
Working Chamber Volume(L)	1000L
Temp Rate of Change( ºC /Min)	15 ºC /Min
Temperature Range	-70 ºC~+100 ºC( Rapid Temp Change -55 ºC~+85 ºC Full Linear Control)
Humidity Constancy	±0.5 ºC
Temp Constancy	±3.0 ºC
Exterior Material	Cold-rolled steel sheet (Rust proof & Plastic Spray treated )/ Stainless Steel
Interior Material	Stainless Steel Plate(SUS 304)
Insulation Material	Rigid Polyurethane Foam
Safety Devices	over pressure,over heat and over current protection for compressor, over temp. protection,
Compressor	Semi-Hermetic Compressor
Cooling Mode	Water Cooled
Control system	Balanced Temperature & Humidity Control System(BTC type)
Heater	Iron-chrome wire heater
Blower	Centrifugal Blower
Observation Window	Glass incorporating heat generator
Temp Sensor	Pt-100
Controller	Touch screen programmable controller
Ambient Temp.	+5ºC~+35ºC
Power	AC 380V/50Hz 3phase 5 wires+ Ground wire
Note: 1. We reserve the right to change specifications without prior notice 2. Customized sizes and configurations available

4. Factory Tour --- Why KOMEG IS Your Right Choice?

Specialized in climatic test chamber since 1990
Main parts are imported famouse brand like Tecumseh, Danfoss, Bizter, ESK,Ranco,Castel,etc.
Passed ,CE,TUV,etc. third party certification
Recognized by Global 500 Enterprises like EMERSON, SIEMENS, Minolta, Epson, HUAWEI, TCL,etc
Environmental friendly, low energy consumption and easy maintenance
High cost-effective and steady delivery time
Experienced and trained staffs assure good service