Specifications

1.novel appearance
2.low consumption, long lifespan(fifty thousand for average life)
3.resistance impact , High reliability

Second-Generation Square LED Wall Washer Instruction

l     Products name ,Part No

WW4020---12 PCS LED,1W high power led ,Pure white,

VotageAC100-240V

WW4017---12 PCS LED,1W high power led ,Pure white,

Voltage:AC100-240V

WW4021---24PCSLED, 1W high power led ,Pure white,

VotageAC100-240V

WW4018---24PCSLED, 1W high power led ,RGB, VotageAC100-240V

WW4022---36PCSLED, 1W high power led ,Pure white, VotageAC100-240V

WW4019---36PCSLED, 1W high power led ,RGB, VotageAC100-240V

l       Product Introduction

Second-Generation Square LED Wall Washer adopts 1W high power LED as light source. It has features , of novel appearance ,low consumption, long lifespan(fifty thousand for average life), resistance impact , High reliability, environment-friendly, soft light, high brightness and so on. This new type of led wall washer made up of two parts, first part is light body and the other one includes power supply and controller box, which makes this wall washer different with other wall washers so that let it have good heat-dissipating function.

 

Single color:Pure white,warm white,red,green,blue,Viewing angle:30°

 

RGB color:Viewing angel is 50°,built-in 13 kinds of light effect,also can separately connect DMX console ,DMX controller box to achieve the color change control in whole or segments,such as red,green,blue,jump change ,gradual , flicker etc.totally 14 types. It is with digital display window and control buttons to let the customers adjust stand-alone mode more convenient.

• Application

Its IP Rank is IP65It can adapt to Various temperature, humidity difference and be widely used for all kinds of wall lighting decoration, as well as in stage,park, ancient building crowd, and civilization plaza etc. 

 

 

 

l       Technique Parameter:

 

 

Item NO.	WW4020		WW4021	WW4022	WW4017	WW4018	WW4019
Light Quantity	12led		24led	36led	12led	24led	36led
Rated Voltage	AC100~240V
MAX Power	16.2	29		56	16.8	29.6	56.5
Luminous Flux	780	1325		2206	270	500	740
Viewing Angle	30°Bead surface	30°Bead surface		30°Bead surface	50°Matte surface	50°Matte surface	50°Matte surface
Light Source	1W high power single colorLED				1W high power RGB color LED
Length of Standard exposed wire	1m
Signal Standard					DMX512 agreement, RGB 3 channels
Connection port	Power supply:3-pin rubber bare wire 3X1.0mm2				Power supply:3-pin rubber bare wire 3X1.0mm2   Signal wire:2-pin Shielding wire ( T-type wire,IP68 Connector)
Net Weight	2.3	4.4		5.9	2.4	4.5	6
IP Rank	IP65

 

 

 

l       Attention

1.Please consider about” the working condition”, the lamp can not be put in water for long time

2.Each RGB wall washer takes up 3 DMX addresses, the first wall washer’s address plus 3 is the address for the next one.

3.If you want all connected wall washers to change colors together, you should set the same address for all the washers

4.Please set the address from smaller to bigger.

>The maximum address of RGB wall washer should be less than 510.

>There should be only one main flood light as a master (the flood light works in main control mode, control box or control console).

5.When there are many wall washer connected together, the connections please refer to the connection diagram.

6.The connection cable between two controllers, or between console and signal amplifiers. It can’t exceed 100m; The distance between the first signals amplifier or console and the last flood light can’t exceed 100m.

 

 

 

Instruction for installation

 

1. The wire of power supply and signal of last wall washer of each loop should be used tail plug for waterproof
2. Please make sure there is no short circuit before turn on the power, otherwise the parts of the device would be burn out.
3. Around the lamp should fill with some gravel or sand when installation, it is better for the heat rink and drainage. And make sure there is no corrosive, inflammability and explosive material around.

 

Note: A. Make sure the power is be turned off while installation or dismounting.

 

     B. Please replace with new lamp when the lamp body is defected.

 

 

 

Problems and solutions:

 

1. If the light cannot light up, please check whether it connects with power supply well and whether the switch is on.

 

2. If the light turns on and off frequently, please check whether the connection between power and lamp is fixed enough.

 

Note: Please contact professionals in case of above solutions do not work; please try to contact professionals instead of open the light at once. 

 

 

 

ILLUSION LED LIMITED

 

Address:  Building C, Huilongda Industrial Park, No. 2 of 2nd Industry Road, Shilong Community, Shiyan Town, Bao'an District, Shenzhen, Guangdong, China.

 

Tel: 0755-29453116   29453125   29453129

 

Fax: 0755-29453113

 

Web: