Product Details

ASTM A36 8mm high tensile hot rolled carbon steel plate price

Product Description

ASTM A36 6mm high tensile hot rolled carbon steel plate price

Specifications

1. ISO9001, CE, FPC Certification

2.Manufacturer

3. High quality, sincere service, fair price

4. Excellent Performance

Brand	C	Si	Mn	P	S	Nb	V
A36	0.13-0.19	0.15-0.50	1.20-1.60	≤0.035	≤0.035	0.015-0.060	0.02-0.20

Chemical Requirements

Elements	Grade A, %	Grade B, %	Grade C, %	Grade E, %	Grade F, %	Grade H, %	Grade J, %
Elements	1-1/4 (32)	1-1/4 (32)	1-1/4 (32)	6 (150)	2-1/2 (65)	2 (50)	1-1/4 (32)
Carbon	0.15-0.21	0.12-0.21	0.10-0.20	0.12-0.20	0.10-0.20	0.12-0.21	0.12-0.21
Manganese	0.80-1.10	0.70-1.00	1.10-1.50	0.40-0.70	0.60-1.00	0.95-1.30	0.45-0.70
Phosphorus, max	0.035	0.035	0.035	0.035	0.035	0.035	0.035
Sulfur, max	0.04	0.04	0.04	0.04	0.04	0.04	0.04
Silicon	0.40-0.80	0.20-0.35	0.15-0.30	0.20-0.40	0.15-0.35	0.20-0.35	0.20-0.35
Nickel	-	-	-	-	0.70-1.00	0.30-0.70	-
Chromium	0.50-0.80	0.40-0.65	-	1.40-2.00	0.40-0.65	0.40-0.65	-
Molybdenum	0.18-0.28	0.15-0.25	0.15-0.30	0.40-0.60	0.40-0.60	0.20-0.30	0.50-0.65
Vanadium	-	0.03-0.08	-	^A	0.03-0.08	0.03-0.08	-
Titanium	-	0.01-0.03	-	0.01-0.10	-	-	-
Zirconium	0.05-0.15^B	-	-	-	-	-	-
Copper	-	-	-	-	0.15-0.50	-	-
Boron	0.0025 max	0.0005-0.005	0.001-0.005	0.001-0.005	0.0005-0.006	0.0005-0.005	0.001-0.005
Columbium, max	-	-	-	-	-	-	-


Elements	Grade M, %	Grade P, %	Grade Q, %	Grade R, %	Grade S, %	Grade T, %
Elements	2 (50)	6 (150)	6 (150)	2-1/2 (65)	2 (50)	2 (50)
Carbon	0.12-0.21	0.12-0.21	0.14-0.21	0.15-0.20	0.10-0.20	0.08-0.14
Manganese	0.45-0.70	0.45-0.70	0.95-1.30	0.85-1.15	1.10-1.50	1.20-1.8
Phosphorus, max	0.035	0.035	0.035	0.035	0.035	0.035
Sulfur, max	0.04	0.04	0.04	0.04	0.04	0.01
Silicon	0.20-0.35	0.20-0.35	0.15-0.35	0.20-0.35	0.15-0.35	0.40-0.60
Nickel	1.20-1.50	1.20-1.50	1.20-1.50	0.90-1.10	-	-
Chromium	-	0.85-1.20	1.00-1.50	0.35-0.65	-	-
Molybdenum	0.45-0.60	0.45-0.60	0.40-0.60	0.15-0.25	0.10-0.35	0.45-0.60
Vanadium	-	-	0.03-0.08	0.03-0.08	-	0.03-0.08
Titanium	-	-	-	-	^c	-
Zirconium	-	-	-	-	-	-
Copper	-	-	-	-	-	-
Boron	0.001-0.005	0.001-0.005	-	-	0.001-0.005	0.001-0.005
Columbium, max	-	-	-	-	0.06	-

1)May be substituted for part or all titanium content on a one for one basis.

2)Zirconium may be replaced by cerium. When cerium is added, the cerium/sulfur ratio should be approximately 1.5 to 1, based upon heat analysis.

3)Titanium may be present in levels up to 0.06% to protect the boron additions.

Tensile & Hardness Requirements
NOTE 1 - On plates wider than 24 in. (600 mm), the test specimen shall be taken in the transverse direction. (See Section 10 and Specification A 6/A 6M)

NOTE 2 - Either the full thickness rectangular specimen shown in Fig. 3 of the Methods and Definitions A 370, or the 1/2-in. (12.5-mm) diameter specimen shown in Fig. 4 of Methods and Definitions A 370 may be used for plates over 3/4 to 1-1/2 in. (20 to 40 mm) in thickness.

Thickness, in. (mm)	Ultimate Tensile Strength ksi (MPa)	Yield Strength^Amin, ksi (MPa)	Elongation in 2 in. (50 mm), ^B,C,D,E	Reduction of Area,^B,C	Brinell Hardness^FNumber
To 3/4 (20), incl	110 to 130 (760 to 895)	100 (690)	18	40^G	235 to 293
Over 3/4 to 2-1/2 (20 to 65), incl	110 to 130 (760 to 895)	100 (690)	18	40^G, 50^H	-
Over 2-1/2 to 6 (65 to 150), incl	100 to 130 (690 to 895)	90 (620)	16	50^H	-

1)Measured at 0.2% offset or 0.5% extension under load as described in the Determination of Tensile Properties section of Methods and Definitions A 370.

2)Elongation and reduction of area not required to be determined for floor plates.

3)For plates tested in the transverse direction, the elongation minimum percent is reduced by 2% and the reduction of area minimum requirement is reduced by 5%.

4)When measured on the Fig. 3 (Methods and Definitions a 370) 1-1/2 in. (40mm) wide specimen (see Note 2 of this table), the elongation is determined in a 2 in. (50-mm) gage length which includes the fracture and shows the greatest elongation.

5)For nominal thickness under 5/16 in. (8 mm), a deduction from the specified percentage of elongation shall be made for decreases of the nominal thickness below 5/16 in (8 mm). See elongation requirement adjustments under the Tension Tests section of Specification A 6/A 6M, for deduction values. However, the deduction may not exceed 3%.

6)See Section 8 of this specification.

7)When measured on the Fig. 3 (Methods and Definitions A 370) 1-1/2 in.(40mm) wide, specimen (see Note 2 of this table).

8)When measured on the Fig. 4 (Methods and Definitions A 370) 1-1/2 in.(12.5mm) round specimen (see Note 2 of this table).

Product Pictures

Packaging & Shipping

Our products

Our Factory

Certificates

FAQ

1.Q:You are Factory or Trading Company?

A: We are trading company authorized by the big mills ,our main products include Steel plate,Steel Bar, Steel coils.

2. Q:What’s the MOQ?

A:Generally,the trail order will be accepted.The MOQ can be confirmed according to the different products. For example,the MOQ of steel plate steel coils and steel bar will be 25-50MT,

3.Q:Do you have OEM service?

A: YES.Variety of products size, quality and quantity can be customized according to your need.

4. Q:could you support free sample?

A:YES.We can supply FREE samples.But the delivery charges will be covered by our customers.

5.Q: How about the delivery time?

A:T/T,30 deposit,70% balance before shipment.Within 15-30 days after receiving the deposit .

6. Q:How about the trade terms?

A:EXW,FOB,CFR,CIF will be accepted.

7.Q:How about your payment terms

A:30%TT in advance and the 70% balance before shipment.

8.Q:Which is your loading Port?

A: Qingdao Port, Tianjin Port, Shanghai Port;