Product Details

Oilfild downhole motor drilling equipment

Downhole motor is a king of downhole dynamic drilling tool upon the power of drilling mud. Mud stream from the outlet of mud pump flows through a dump value into the motor. This stream produces pressure loss at both inlet and outlet of the pump, to push the motor into rotating, and to transmit the torque and speed onto the bit. The downhole motor property mainly depends upon its property parameters.
We can supply difference types of downhole motor, from 60 to 244mm in diameter, 3.5MPa, 7MPa and 14MPa pressure series, including single lobe and multi-lobe, single bent and double bents motors, which can match different kinds of stabilizers. Chinese manufacturers have the ability to develop a variety of down-hole motors in independence.

Detail Specification

Drill tool type		5LZ73 ×7.0	5LZ89 ×7.0	5LZ95 ×7.0	7LZ95 ×7.0	9LZ95 ×7.0	7LZ102 ×7.0	5LZ 120 ×7.0 IV	5LZ 120 ×7.0 III	5LZ 165 ×7.0	5LZ 165 ×7.0 IV
Hole size	in	3 1/2~ 4 3/4	4 1/2 ~6	4 5/8~ 6	4 5/8~ 6	4 5/8~ 6	4 5/8~ 6	5 7/8~7 7/8	5 7/8~ 7 7/8	8 3/8~ 9 7/8	8 3/8~9 7/8
Advise flow	l/s	2~4	3~8	7~12	8~13	6~10	8~13	9~14	9~16	20~28	20~28
Drill speed	rpm	125~270	95~250	90~240	80~205	90~185	80~205	95~250	95~250	90~200	90~200
Motor pressure drop	Mpa	2.4	2.4	3.2	2.4	2.4	2.4	2.4(3.2)	2.4	2.4	3.2
Working torque	N.m	320	560	1100	1200	900	1200	1350(1800)	1700	3300	4500
Output power	Kw	4.2~7.4	5.6~11.7	10.4~22.5	10~20.7	8.5~14	10~20.7	13.4~28.3 (17.9~37.7)	16.9~35.6	11.1~55.3	42.4~75.4
Circulating opening pressure drop	Mpa	1.4~7	1.4~7	1.4~7	1.4~7	1.4~7	1.4~7	1.4~7	1.4~7	1.4~7	1.4~7
Advise bit load	MT	1.5	2	2.5	2.5	2.5	2.5	3 (4)	3	6	8
Max bit load	MT	2	3	5	5	4	5	5	5	16	16
Length	mm	3670	2700	4200	4035	4389	4185	3900	4555	5700	6930
Upper end worm	REG	2 3/8	2 3/8	2 7/8	2 7/8	2 7/8	2 7/8	3 1/2	3 1/2	4 1/2	4 1/2
Lower end worm	REG	2 3/8	2 3/8	2 7/8	2 7/8	2 7/8	2 7/8	3 1/2	3 1/2	4 1/2	4 1/2
AKO		0.25°, 0.5°, 0.75°, 1°, 1.25°, 1.5°, 1.75°, 2°, 2.25°, 2.5°
DTU		0.6°, 0.75°
FAB		1°×2.5°, 1°×0.5°, 1°×0.75°, 1°×1°, 1°×1.25°, 1°×1.5°, 1°×1.75°, 1°×2°, 1°×2.25°, 1°×2.5°