Specifications
hydraulic rotary core drill rig1)hydraulic drive
2)Drilling depth:1300m
3)weight:9000kg
4)drill rig power:132Kw
hydraulic rotary core drilling rig HGD-1000
Introduction:
HGD-1000 full hydraulic tracked core drilling rig , is a new generation of full hydraulic rig, which can replace the same type of imported products and even has higher cost performance. The rig hydraulic and mechanical system adopt mature and advanced techniques, the hydraulic system adopts load-sensing control system and the highly reliable configured hydraulic components, and the mechanical shift system adopts remote operation of synchronous gear shift, all of which are applicable to many kinds of drilling, the whole rig has many advantages, such as great engine power, multi-functional output torque, high efficiency, excellent flexibility, good stability and multi-functional.
Technological data of full hydraulic rotary core drilling rig
Height | 2400mm | Width | 2400mm |
Length | 5000mm | Height of caterpillar | 600mm |
Width of caterpillar | 400mm | Maximum climbing angle | 30° |
Walking speed max | 2km/h | Total weight | 9000kgs |
1.Drilling capacity | 5. Main Hoist (Made in USA) |
| |||
Drilling rod diameter | drilling depth | Drive Mode | Hydraulic |
| |
55.5mm | 1300m | Lifting power | 68 KN(bare drum) |
| |
75mm | 1000m | lifting speed | 50m/min(bare drum) |
| |
89mm | 700m | steel wire rope diameter | 16mm |
| |
114mm | 400m | Rope capacity | 30m |
| |
2.Power Systems | 6. Wireline Hoist |
| |||
model | Cu Commins 6CTA diesel engine | Drive Mode | Hydraulic |
| |
Cylinder volumn | 5.9L | Lifting power | 13.5 KN (bare drum) |
| |
Cylinder number | (6 cylinder in-line) | Lifting speed | 100m/min(bare drum) |
| |
type | turbocharge | Steel wire rope diameter | 5mm |
| |
cooling type | water-cooled | Rope capacity | 1200m |
| |
power | 132KW 2500 r/min | 7. Sliding-type mast |
| ||
3. Hydraulic System | The mast is divided into two sections, upper mast and lower mast (central collapsible to facilitate transport), The mast can also slip longitudinally to support on the ground. |
| |||
Fixed actuating pressure | 28MPa |
| |||
cooling type | air-cooled |
| |||
4. rotation head |
| mast length | 10m |
| |
Drive Mode | Hydraulic driving | Landing approach | Hydraulic driving |
| |
Max torque | 4500N.M | drilling angle | 45-90 |
| |
Max hole diameter | 117mm | driving force | 62KN |
| |
Transmission | 4 shifts manual actuated | lifting power | 189KN |
| |
speed | feeding stroke | 3600mm |
| ||
first position | 140-190 r/min | Slippage Stroke of mast | 1100mm |
| |
second position | 280-380r/min | 8. clamp | |||
third position | 495-675r/min | The open and close form | all by hydraulic pressure |
| |
fourth position | 865-1200 r/min | max hole diameter | 117mm |
| |
The open and close form of power head chuck
| dyadic hydraulic pressure chuck, clamp by imported polyurethane ester spring, loose by hydraulic pressure.
| 9. Crawler-type undercarriage system |
| ||
control model: | hydraulic |
| |||
Caterpillar Wheelbase | 2000mm |
| |||
max traction power | 100KN |
| |||
10. 110KN |
| ||||
type | BW250-L |
| |||
Max flow | 250 L/min |
| |||
Max pressure | 20Mpa |
| |||
