Specifications

1.Trailer body material :galvanized plate then powder coated
2.Easy open with 45 secondes
3.Off -road with dual shorck

 

Dimension:

1.Trailers size: 3900*1920*1700mm(L*W*H)

2.Trailer box size:2400*1920*1080mm(L*W*H)

3.Inner size of solar panel steel bracket: 1370*2230m(not including solar panel)

4.Net weight of trailers: 960Kg

5.Draw bar material: Q345

Features:

1.4wd 360 degree off road coupling, with hand brake, in accord with Australia standard.

2.Jockey wheel:Inflatable and Solid jockey wheel

3.Stone guard & spare wheel carrier on tailgate

4.Large tool box on driver’s side

5.Wiring harness under trailer concealed in steel conduit 

6.Jerry can Holder for 9 Kg Jerrycans

7.Kitchen Assembly –Demountable with stove slide 

8.Leaf spring suspension (Independent suspension is available)

9.10” electric brakes with mechanical over ride back up 

10.Galvanized sheet, then fully powder coated finish

11.Powder coated finish to camper metalwork 

12.Boat rack side cast for 60Kg boat prewired for solar option

13.Boat motor mount for 30Kg motor located on front tailgate

14.Twin fridge frame inside front tailgate

15.Dedicated position for generator

16.LED tail lights, turn indicators and number plate lights

17.Rims 16” 6-stud pattern *3

18.Storage cubes in kitchen with water hand pump hose

19.Pre-stressed, reinforced drawbar

20.Trailers can be built as per customer/s special requirements

Tent spec:

14OZ Rip-stop,rain-stop canvas tents available for choice

Size:25 square meters

Rated for 6-8 persons

Clear PVC overlays for tropical windows *2

Queen size high density foam mattresses *2

2* Ladders to bed area

Marine carpet to floor of tent area-floor protection 

Full length tropical windows*3

Mesh Floor protector under tent and floor to annex

Midgy proof fly mesh used on all windows and gazebo

Shade awning off main bed windows *2

Poles, ropes and pegs for annex and awnings

Hammer/Peg puller

Optional:

Gas burners with AGA, Jerry can, Solar panel

 

 

 

 

Material
1.1 GRADE
DuraGal angles,channels and flats are manufactured by a cold forming process which ensures that it complies with the requirements shown below
section	Actual thickness             t                 mm	Grade	Minimum   Yield     Stress         Mpa	Minimum Tensile Strength   MPa	Minimum Elongation as a proportion of Gauge Length of 5.65                 %
Flats	t≤6.0     t>6.0	C400LO     C350LO	400             350	450       400	20                           20
Angles and Channels	t≤6.0         t>6.0	C400LO     C400LO	450           400	500         450	16                             16
DuraGal profiles comply with the requirements of steel type 7B in Talbe 10.4.1 of AS4100.
LO indicates that DuraGal profiles have Charpy V-notch impact properties as specified in TS100[11]. Table 10.4.1 of AS4100 Steel Structures permits impact tested LO grades to have the following minimum servicetemperature:
	Actual thickness   mm	Lowest one day mean ambient Temperature         ºC
	t≤5	-30
	5<t≤10	-20
1.2   SURFACE FINISH
A minimum of 100g/m² coating of zinc is applied by in-line galvanising to a mechanically(shot blasted)and chemically cleaned bright metal(AS 1627.4 Class 3.0) surface. A clear polymer barrier coating protects the protects the galvanising prior to fabricartion.
1.3 SIZE RANGE
	Equal Angles	Unequal Angles	Channels	Flats
	30x30 to 150x150	75x50	75x40 to 300x90	50to300

 

 

Craft : blanking,stamping, grilding,welding,assembling,painting, baking etc.

 

Blanking workshop

 

 

surface finishing--- painting finish or baking finish

 

Fiberglass workshop

 

 

 

 Assembly shop

 

 

Delivery

 

 

Our certification: 

 

 

Our products & factory: