Specifications

Pre-heating Copper Coil Galvanized Steel Solar Water Heater System ( H )
The water is clean than non-pressure system

Technical data

1.Inner tank:SUS304-2B food grade stainless steel with thickness 0.4mm,360mm diameter. 

2.Outer tank:galvanized steel with white paint, 0.4mm thickness ,470mm diameter

3.Vacuum tube:3 target / golden purple vacuum tube ,58mm*1800mm

4.Bracket: galvanized steel with green  paint ,1.5mm thickness. 

5.Insulation layer:high-pressure automatic polyurethane foaming layer with thickness 55mm.

6Heat preservation:72 Hours.

Feature

1.A copper coil is installed inside the tank as the heat exchanger.

2.When water flows into the copper coil,it absorbs heat from the water in the tank,therefore,

the water tank is just a heat storage.

3.Use at any time.It adopts advanced desigh idea and integrated with high efficiency preheated  patent

technique,so it can warm the cold water rapidly when it flows through special pipe.It can overcome the short of traditional solar water heater ,such as slow heating,long  waiting time.

4.More capacity.We adopt special exchanging heat mode ,it avoids mixed effect ,so cold water can be heated at any moment.

5.Easy operation.It can supply water automatically ,u can take it easy and enjoy good time.

 

The water of the heat preservation water tank is just decalescence, heat accumulation and thermolysis the water of the water tank is invariableness. The vacuum tube collector absorb the heat energy to heat the water in heat storage tank, when using the hot water, the cold water flows through the inlet, the copper coil absorb the heat then transfer into the cold water ,so that the temperature rise up ceaseless, for the original features of the copper coil, the water temperature of the outlet is close to the water temperature of the water tank(≤3), so the high pressure of the cold water into the copper coil and absorb the temperature, at last the water can be used.
Pre-heated pressured solar collectors provides mains pressure pre-heating via a high efficiency copper coil heat exchanger located within the solar collector tank. The way in which the Mains Pressure solar collector heats water is the same as the Non pressure solar collector.. Rather than using the water in the tank directly, as the Non pressure does, the type uses a 4560 copper coil. Heat exchanger inside the tank which provides more than 1.2m2 of heat transfer area. When water flows though the coil it absorbs heat from the water inside the solar collector tank. The solar collector tank is therefore a thermal store. One advantage of this system is that almost no water is introduced into the tank (apart from occasional topping up),so corrosion and scale buildup are almost totally eliminated. Tanks are designed for low to medium pressure applications using gravity feed tank or pressure reduction valve. Direct connection to mains pressure water supply is not permitted. Please check your local building/plumbing regulations regarding the installation of water tanks.

 

 

Descripition	Pre-heated solar water heater
Material of out tank	0.4mm thickness PVDF galvanized steel
Material of inner tank	Food grade 0.4mm thickness SUS304 stainless steel
Heat exchange coil	T2 Red copper, Ø12mm, 1.0mm thickness
Tank insulating layer	50kg/m³ high-density polyurethane foam, 55mm thickness
Structure of tank:	Copper coil inlet/outlet : G1/2” male  Air vent: G 1/2” male  ,   (Optional) Electric heater:1”, Could water inlet:  G1/2” male, drainage: D47mm
Welding:	Argon arc welding, spot welding
Working pressure	Copper coil: 0.6Mpa (6 bars), tank: 0.005Mpa (0.05 bars)
Solar collector tube	3.3 Borosilicate glass with Cu-SS/Aln coating
glass tube thickness	1.6mm
Vacuum tube tightness	P≤0.005 Pa
Absorption	as=0.94-0.97(AM1.5)
Emission ratio	εh=0.03-0.05(80C±5C)
Idle sunning property parameters	Y=220~260m2.C/KW
Average heat loss coefficient	ULT=0.6~0.7W/(m2.C)
Bracket:	1.5mm thickness PVDF galvanized steel
Frame angle options	15°/25°/27°/30°/35°/45°/52°    <Please select specific angle when you order>
Fastening pieces:	Made of stainless steel screw
Max working  temp.:	99°C
Hail resistance:	Ø25mm
Anti Freezing:	-20°C
Wind resistance:	20m/s
Instruction manual:	Available
Accessory:	Assistant tank(8L), electric heater (1.5/2/2.5kw),

 

 

Model list: 

Item No.	Solar Vacuum Tube		Absorber      Area	Tank Capacity	Serve people	Loading Qty / sets
	pcs	size / mm				20GP/40GP/40HQ
YR-TS-20	20	Φ58 X 1800	2.94	200L	3~4	34/72/84
YR-TS-24	24	Φ58 X 1800	3.53	240L	4~5	31/65/77
YR-TS-30	30	Φ58 X 1800	4.43	300L	5~6	22/50/58
YR-TS-36	36	Φ58 X 1800	5.32	360L	7~8	16/40/43