MODEL

PT-6503

OUTPUT

OUTPUT NUMBER

CH1

CH2

CH3

DC VOLTAGE

3.3V

5V

12V

RATED CURRENT

6A

6A

1A

CURRENT RANGE    

0 ~ 7A

0.2 ~ 10A

0 ~ 1.2A

RATED POWER

Total power max. 61.8W(CH1+CH2 max. 54W)

RIPPLE & NOISE (max.) Note.2

50mVp-p

50mVp-p

100mVp-p

VOLTAGE ADJ. RANGE

CH1: 3 ~ 3.6V

VOLTAGE TOLERANCE Note.3

±3.0%

+4, -2%

±8.0%

LINE REGULATION    

±1.0%

±1.0%

±2.0%

LOAD REGULATION  

±3.0%

±3.0%

±8.0%

SETUP, RISE TIME

800ms, 50ms at full load

HOLD UP TIME (Typ.)

60ms at full load

INPUT

VOLTAGE RANGE

90 ~ 264VAC         127 ~370VDC

FREQUENCY RANGE

47 ~ 63Hz

EFFICIENCY (Typ.)

72%

AC CURRENT(Typ.)

1.8A/115VAC         0.9A/230VAC

INRUSH CURRENT (Typ.)

COLD START 20A/115V         40A/230V

LEAKAGE CURRENT

<1mA / 240VAC

PROTECTION

OVERLOAD

120~ 160%rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed.

OVER VOLTAGE

5.75 ~ 6.75V on +5V

Protection type:Hiccup mode, recovers automatically after fault condition is removed

ENVIRONMENT

WORKING TEMP.

-10~+60°C (Refer to "Derating Curve")

WORKING HUMIDITY

20~90% RH non-condensing

STORAGE TEMP., HUMIDITY

-20~+85°C,10~95% RH

TEMP. COEFFICIENT

±0.03%/°C(0~50°C)

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY&EMC

(Note 4)

SAFETY STANDARDS

UL60950-1, TUV EN60950-1 approved

WITHSTAND VOLTAGE

I/P-O/P:3KVAC     I/P-FG:1.5KVAC     O/P-FG:0.5KVAC 1min.

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH

EMC EMISSION

Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,11, light industry level, criteria A

OTHERS

MTBF

222Khrs min MIL-HDBK-217F(25°C)

DIMENSION

127*76*42mm (L*W*H)

PACKING

0.28Kg; 54pcs/16.2Kg/1.35CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”

5. Mounting holes M1 and M2 should be grounded for EMI purposes.

6. Heat Sink HS1,HS2 can not be shorted.