MODEL

PLC-30-36

OUTPUT

DC VOLTAGE

36V

CONSTANT CURRENT REGION Note.6

25.2 ~ 36V

RATED CURRENT

0.84A

CURRENT RANGE

0 ~ 0.84A

RATED POWER

30.24W

RIPPLE & NOISE (max.)         Note.2

3.6Vp-p

VOLTAGE ADJ. RANGE     Note.5

34.2 ~ 39.6V

CURRENT ADJ. RANGE     Note.5

0.63 ~ 0.865A

VOLTAGE TOLERANCE       Note.3

±10%

LINE REGULATION

±3.0%

LOAD REGULATION

±5.0%

SETUP, RISE TIME         

2000ms / 230VAC   3000ms / 115VAC at full load

INPUT

VOLTAGE RANGE          Note.4

90 ~ 264VAC 127 ~ 370VDC

FREQUENCY RANGE 

47~63HZ

POWER FACTOR (Typ.)

PF>0.95/115VAC, PF>0.9/230VAC at full load (Please refer to "Power Factor Characteristic" curve)

EFFICIENCY (Typ.)

85%

AC CURRENT(Typ.)

0.4A/115VAC     0.2A/230VAC

INRUSH CURRENT (Typ.)

COLD START 35A(twidth=25us measured at 50% Ipeak) at 230VAC

LEAKAGE CURRENT

<0.5mA / 240VAC

PROTECTION

OVER CURRENT   Note.4

100 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed.

OVER VOLTAGE  

40 ~ 50V

Protection type : Shut down o/p voltage, re-power on to recover

OVER TEMPERATURE

95°C±10°C (TSW1)

Protection type : Shut down o/p voltage, re-power on to recover

ENVIRONMENT

WORKING TEMP.

-30~ +50°C(Refer to "Derating Curve")

WORKING HUMIDITY

20 ~ 95% RH non-condensing

STORAGE TEMP., HUMIDITY

-40 ~ +80°C, 10 ~ 95% RH

TEMP. COEFFICIENT

±0.06%/°C (0 ~ 50°C)

VIBRATION

10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes

SAFETY&EMC

SAFETY STANDARDS   Note.6

UL1310, TUV EN61347-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91(except for 48V), J61347-1, J61347-2-13 approved

WITHSTAND VOLTAGE

I/P-O/P:3.75KVAC

ISOLATION RESISTANCE

I/P-O/P:100M Ohms / 500VDC / 25°C/ 70% RH

EMC EMISSION

Compliance to EN55015, EN61000-3-2 Class C (Pin ≥25W), Class D( >70% load),EN61000-3-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61547, light industry level, criteria B

QTHERS

MTBF

625.5K hrs min. MIL-HDBK-217F (25°C)

DIMENSION

160*46*30mm (L*W*H)

PACKING

0.2Kg; 70pcs/15Kg/0.96CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 °C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics for more details.

5. Output voltage can be adjusted through the SVR1 on the PCB; limit of output constant current level can be adjusted through the SVR2 on the PCB.

6. Constant current operation region is within 70% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please

reconfirm special electrical requirements for some specific system design.

7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

8. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.