MODEL

MSP-100-48

OUTPUT

DC VOLTAGE

48V

RATED CURRENT

2.2A

CURRENT RANGE

0 ~ 2.2A

RATED POWER

105.6W

RIPPLE & NOISE (max.)   Note.2

240mVp-p

VOLTAGE ADJ. RANGE

45.6 ~ 55.2V

VOLTAGE TOLERANCE Note.3

+1.5%

LINE REGULATION    

±0.2%

LOAD REGULATION    

±0.5%

SETUP, RISE TIME

2500ms, 100ms/230VAC 2500ms, 100ms/115VAC at full load

HOLD UP TIME (Typ.)

50ms/230VAC         20ms/115VAC at full load

INPUT

VOLTAGE RANGE     Note.5

85 ~ 264VAC         120 ~ 370VDC

FREQUENCY RANGE

47~63HZ

POWER FACTOR (Typ.)

PF>0.95/230VAC   PF>0.98/115VAC at full load

EFFICIENCY (Typ.)

90%

AC CURRENT (Typ.)

1.2A/115VAC       0.6A/230VAC

INRUSH CURRENT (Typ.)

35A/115VAC         65A/230VAC

LEAKAGE CURRENT   Note.7

Earth leakage current < 300£gA/264VAC , Touch leakage current < 100uA/264VAC

PROTECTION

OVER LOAD

105 ~ 135% rated output power

Protection type : Constant current limiting for Vo=50 ~ 100% of rated voltage, recovers automatically after fault condition is removed

OVER VOLTAGE

57.6 ~ 67.2V

Protection type : Shut down o/p voltage, re-power on to recover

OVER TEMPERATURE

90°C(3.3V ~ 7.5V) , 85°C(12V ~ 48V) (TSW1 : detect on heatsink Q101 of power transistor)(optional)

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down.

FUNCTION

REMOTE CONTROL

RC+/RC- : 0 ~ 0.8V= power on ; 4 ~ 10V = power off

ENVIRONMENT

WORKING TEMP.

-40~+65°C (Refer to derating curve)

WORKING HUMIDITY

20~90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40~+85°C, 10~95%RH

TEMP. COEFFICIENT

±0.04%/°C(0~ 50°C)

VIBRATION

10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes

SAFETY&EMC

(Note 4)

SAFETY STANDARDS

ANSI/AAMI ES60601-1, IEC60601-1 approved

WITHSTAND VOLTAGE

I/P-O/P:4KVAC     I/P-FG:2KVAC     O/P-FG:0.5KVAC

ISOLATION RESISTANCE

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C/ 70% RH

EMC EMISSION

Compliance to EN55011 (CISPR11) Class B, EN61000-3-2,-3

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, EN60601-1-2

OTHERS

MTBF

295.7K hrs min.      MIL-HDBK-217F (25°C)

DIMENSION

159*97*38mm (L*W*H)

PACKING

0.38Kg; 24pcs/10.1Kg/0.76CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance: includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.

5. Derating may be needed under low input voltages. Please check the derating curve for more details.

6. No load power consumption<0.5W when RC+ & RC- (CN100 pin1,2) 0 ~ 8V or short.

7. Touch current was measured from primary input to DC output.

8. When the input voltage is less than 40VAC, the SPS may exhibit degradation of performance. The final product manufacturers must re-confirm this

deviation that does not affect basic safety or essential performance.