ORDER NO.

GS280A15-C4P

OUTPUT

SAFETY MODEL NO.

GS280A15

DC VOLTAGE         Note.2

15V

RATED CURRENT

16A

CURRENT RANGE

0 ~ 16A

RATED POWER(max.)

240W

RIPPLE & NOISE (max.)   Note.3

120mVp-p

VOLTAGE TOLERANCE      Note.4

±5.0%

LINE REGULATION       Note.5

±1.0%

LOAD REGULATION     

±5.0%

SETUP, RISE TIME    Note.6

2000ms, 20ms / 230VAC 2000ms, 20ms / 115VAC at full load

HOLD UP TIME (Typ.)

16ms / 230VAC 16ms / 115VAC at full load

INPUT

VOLTAGE RANGE      Note.7

90 ~ 264VAC     120 ~ 370VDC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACTOR (Typ.)

PF>0.95 / 230VAC PF>0.98 / 115VAC at full load

EFFICIENCY (Typ.)  

89.5%

AC CURRENT(Typ.)

3A / 115VAC 1.5A / 230VAC

INRUSH CURRENT (max.)

120A / 230VAC

LEAKAGE CURRENT(max.)

1.5mA / 240VAC

PROTECTION

OVERLOAD  

105 ~ 135%rated output power

Protection type : Hiccup mode, recovers automatically after fault condition is removed

OVER VOLTAGE

105 ~ 135%rated output voltage

Protection type : Shut down o/p voltage, re-power on to recover

OVER TEMPERATURE

100°C ±10°C (RTH2)

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

ENVIRONMENT

WORKING TEMP.

-30 ~ +60°C(Refer to "Derating Curve")

WORKING HUMIDITY

20%~90% RH non-condensing

STORAGE TEMP., HUMIDITY

-40~+85°C, 10~95%RH

TEMP. COEFFICIENT

±0.03%/°C (0~40°C)

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

SAFETY&EMC (Note. 8)

SAFETY STANDARDS

UL60950-1, TUV EN60950-1, BSMI CNS14336, CCC GB4943, J60950-1(except for 48V) approved

WITHSTAND VOLTAGE

I/P-O/P:3KVAC

ISOLATION RESISTANCE

I/P-O/P:100M Ohms /500VDC/25°C/70% RH

EMC EMISSION

Compliance to EN55022 class B, EN61000-3-2,3, FCC PART 15 / CISPR22 class B, CNS13438 class B, GB9254 class B

EMC IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11, light industry level, criteria A

OTHERS

MTBF

173.6Khrs min. MIL-HDBK-217F(25°C)

DIMENSION

220*95*46mm (L*W*H)

PACKING

1.25Kg; 12pcs/16Kg/1.27CUFT

CONNECTOR

PLUG

See page 2 ; Other type available by customer requested

CABLE

See page 2 ; Other type available by customer requested

NOTE

1.All parameters are specified at 230VAC input, rated load, 25°C 70% RH ambient.

2.DC voltage: The output voltage set at point measure by plug terminal & 50% load.

3.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor.

4Tolerance: includes set up tolerance, line regulation, load regulation.

5.Line regulation is measured from low line to high line at rated load.

6.Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.

7 Derating may be needed under low input voltages. Please check the derating curve for more details.

8. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meetsEMC directives.