ORDER NO. | GS120A48P1M | ||
OUTPUT | SAFETY MODEL NO. | GS120A48 | |
DC VOLTAGE | 48V | ||
RATED CURRENT | 2.5A | ||
CURRENT RANGE | 0 ~ 2.5A | ||
RATED POWER | 120W | ||
RIPPLE & NOISE (max.) Note.2 | 240mVp-p | ||
VOLTAGE TOLERANCE Note.3 | ±2.0% | ||
LINE REGULATION Note.4 | ±1.0% | ||
LOAD REGULATION | ±2.0% | ||
SETUP, RISE TIME Note.6 | 2000ms, 30ms / 230VAC 2500ms, 30ms / 115VAC at full load | ||
HOLD UP TIME (Typ.) | 20ms / 230VAC 20ms / 115VAC at full load | ||
INPUT | VOLTAGE RANGE Note.7 | 85 ~ 264VAC 120 ~ 370VDC | |
FREQUENCY RANGE | 47 ~ 63Hz | ||
POWER FACTOR (Typ.) | PF>0.97 / 230VAC PF>0.99 / 115VAC at full load | ||
EFFICIENCY (Typ.) | R7B | 91% | |
P1M | 90.5% | ||
AC CURRENT | 1.4A / 115VAC 0.7A / 230VAC | ||
INRUSH CURRENT (max.) | 70A / 230VAC | ||
LEAKAGE CURRENT(max.) | 0.75mA / 240VAC | ||
PROTECTION | OVERLOAD | 105 ~ 160%rated output power | |
Protection type : Hiccup mode, recovers automatically after fault condition is removed | |||
OVER VOLTAGE | 105 ~ 135%rated output voltage | ||
Protection type : Shut down o/p voltage, re-power on to recover | |||
OVER TEMPERATURE | RTH2 > 100°C ±10°C | ||
Protection type : Shut down o/p voltage, re-power on to recover | |||
ENVIRONMENT | WORKING TEMP. | -30 ~ +70°C(Refer to "Derating Curve") | |
WORKING HUMIDITY | 20%~90% RH non-condensing | ||
STORAGE TEMP., HUMIDITY | -40~+85°C, 10~95%RH | ||
TEMP. COEFFICIENT | ±0.03%/°C (0~50°C) | ||
VIBRATION | 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes | ||
SAFETY&EMC (Note. 5) | SAFETY STANDARDS | UL60950-1, TUV EN60950-1, BSMI CNS14336, J60950-1(except for 48V) approved | |
WITHSTAND VOLTAGE | I/P-O/P:3KVAC | ||
ISOLATION RESISTANCE | I/P-O/P:100M Ohms /500VDC/25°C/70% RH | ||
EMC EMISSION | Compliance to EN55022(CISPR22) ,EN61204-3 class B, CNS13438 class B, FCC PART 15, EN61000-3-2,3 | ||
EMC IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,8,11, light industry level, criteria A | ||
OTHERS | MTBF | 400.7K hrs min. MIL-HDBK-217F(25°C) | |
DIMENSION | 167*67*35mm (L*W*H) | ||
PACKING | 0.62Kg; 20pcs/13.4Kg/0.9CUFT | ||
CONNECTOR | PLUG | See page 2 ; Other type available by customer requested | |
CABLE | See page 2 ; Other type available by customer requested | ||
NOTE | 1.All parameters are specified at 230VAC input, rated load, 25°C 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Tolerance: includes set up tolerance, line regulation, load regulation. 4.Line regulation is measured from low line to high line at rated load. 5.The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meetsEMC directives. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. Derating may be needed under low input voltages. Please check the derating curve for more details. | ||