Specifications

1.cable separation recycling equipment
2.High separation rate
3.waste copper wire
4.Separator machinery
5.Cable wire Recyc

  Low Power scrap copper wire recycling machine / cable wire recycling machine      

 

 

Working Principle of  scrap copper wire recycling machine / cable wire recycling machine  :

When directly put into the scrap copper wire recycling machine / cable wire recycling machine , used cable is cut into granules first, 

during this process, copper and plastic is separated but mixed together, then 

the granules are sent to vibrationdevice for separation,through wind blow and 

vibration, the copper and plasticis are separated, then pure copper comes out 

from one side and pure plastic comes out from the other side, we collect the 

separated pure copper and plastic at last!

.

  

  

 

Advantages and Features:

1. · Suits wide range of scrap copper wire recycling machine / cable wire recycling machine :

        Computer wire, Automobile/car wire, Telephone wie, Communication wire&cable etc. 

        Single core, Double core, Multi-core etc.

        We put the waste wire/cable directly in the machine! No matter twisted or tangled together!

        (The diameter should between 0.5-20mm)
      · High efficiency: 99% recycling rate. It can recycle copper/aluminum and plastic at the same time!
      · Energy saving:  scrap copper wire recycling machine / cable wire recycling machine  consumes less energy compared with the same products!                

      · Environmental friendly: no water needed and no air pollution! All the dust is collected.

      · Easy operation: easy installation, devices are fixed on the bottom board, easy to move or transport! 

 

    

 

 

Working steps of Low Power scrap copper wire recycling machine / cable wire recycling machine    

1)Materials are put into the crusher by the belt conveyor.

2)The crushed materials (mixture of copper and plastic) are conveyed to the Vibrating separator by the belt conveyor, during which procedure the plastic granules (including fiber, rope, or tapes, etc. mixed in the wires) are cleaned by the pulse dust collectors .

3)The separator is consist of separating board, eccentric device, adjustable amplitude device,and speed adjustable motor, etc. It is used to separate plastic and copper.

4) After that, the mixer( small part mixer of copper and plastic) will be conveyed to the high voltage electrostatic separator for further processing.

5)All scrap copper wire recycling machine / cable wire recycling machine are installed on the underbed to form a whole structure, easy for transportation. The scrap copper wire recycling machine / cable wire recycling machine  is adjusted ready for production before shipment, and customer only need to connect it to the power supply.

 

   

 

Product features of Low Power scrap copper wire recycling machine / cable wire recycling machine   

1. Eco-friendly. 

The whole scrap copper wire recycling machine / cable wire recycling machine process adopts mechanical power without water or gas, no dust, no pollution.   

2. Incredible recycling rate. 

The test show the recycling rate is up to 99.9%, which is a guarantee of high quality and good market of copper granule processed by our machines.

3. Labor-saving. 

On account of its integrated design and intelligent design, scrap copper wire recycling machine / cable wire recycling machine just needs 1-2 workers to operate, greatly saving your labor cost.

     

 

Features of     

1. Eco-friendly. 

The whole process adopts mechanical power without water or gas, no dust, no pollution.   

2. Incredible recycling rate. 

The test show the recycling rate is up to 99.9%, which is a guarantee of high quality and good market of copper granule processed by our machines.

3. Labor-saving. 

On account of scrap copper wire recycling machine / cable wire recycling machine  integrated design and intelligent design, scrap copper wire recycling machine / cable wire recycling machine just needs 1-2 workers to operate, greatly saving your labor cost.

   

 

Technical Specifications

Working Principle Of Copper Cable Crushing Machine:  

1.After crushing waste wire,the size of plastic grain and the copper grain is similar by a sieve hole;

2.After wind screening classifier and the other copper grain mixture into another a special crusher to achieve plastic and copper grains complete separation;

3.Then into the high voltage separator,in order to complete the sorting effect.

  

 

Main technical parameter of Low Power scrap copper wire recycling machine /rubber separator waste cable wire recycling equipment     :

 

Model	Yuxi-350
Capacity	100-200kg/h
Total Power	17.3KW
Volt	220V,50HZ
Overall Dimension	3.1*2*2.25m
Package Size	3.4*2.27*2.4m
Weight	1.6T
Wire Diameter	0.3mm-25mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Raw Material :

  

 

About us :

 

Working Place :

 

About our factory: 

Through 21 years of development and technology innovation, our Zhengzhou Yu Xi Machinery Equipment Co., Ltd. has been developped to a professional manufacturer set design, manufacture, after-sale service

as a whole. In order to meet the different requirements of our customers, we designed and researched many types of charcoal process machines, include charcoal & coal briquette machine, shisha & hookah charcoal

tablet machines, charcoal & coal extruder machines, and biomass charcoal briquette machines, etc.

Besides, we have also got the CE, ISO, SGS, etc, several patents, and for many years, our machines have been sold home and abroad, and are highly praised by our customers, especially the foreign customers such

as Indonesia, Saudi Arabia, Malaysia, India, South Africa, Canada, Australia, Russia, Spain, Greece, Pakiswait, Turkey, Egypt, Sudan, Uzbekistan, Philippines, and other countries.

 

 

Our service for our customers:

 

♥. Pre-sale service: design and manufacture machines for you as your special requirements, provide you with project, process design, and purchase programm.

 

♥. On-sale service: accompany with you to look around our factory, explain the manufacture process of our machines, and check the working performance of our machines.

 

♥. After-sale service: engineers are available to install and debugging equipments of the whole production line, besides, commissioning and training operators on site.

 

 

Contact with us :