Specifications

Automatic voltage controller 8000
1Voltage regulator
2 Voltage stabilizer
3 Servo stabilizer

•                 AUTOMATIC VOLTAGE CONTROLLER
•            ROLLING CONTACT TYPE
•            SERVO VOLTAGE STABILIZER
•            RANGE 100 KVA TO 8000 KVA
•  Inspite of best efforts, no state electricity board can ensure constant voltage to customer because of long and inadequate distribution and irregular load pattern on distribution transformers. Generally Voltage is low during day time and high during night hours. Moreover on holiday, peak hour’s rainy days and when agricultural and industrial load is switched off,  the voltage rises sharply which is more dangerous. 

• This higher current affects the electrical motors (particularly smaller capacity moters up to 7.5 H.P) in three ways. 

• Higher current produces higher losses in electrical moters which causes premature failure of winding. 

• These higher losses of electric motors also increase the losses of cables, switches, transformers and other associated equipments. 

• For smooth continuous operation of motors, over load relays are usually set at 20% higher setting.
•  With the installation of the stabilizer and maintaining RATED voltage, the motor will operate smoothly drawing 15 - 20% lesser current and correspondingly the relay setting can be reduced by 15-20% In case single phasing occurs, the relays, contractors, switchgears, etc. incorporated with the motor will be safe.                                           

 

• DESCRIPTION OF AUTOMATIC VOLTAGE CONTROLLER:  

• PEC servo Stabilizer primarily consists of the following:- 

• 1.  Linear plus /Minus Type Vertical Rolling Contact Voltage Regulator      
•                                                                                                                                                           
• In our regulator we are using heavy section of electrolytic grade rectangular copper strip instead of copper wire to minimize the losses & increase the efficiency of equipment. We are using self lubricating Carbon Roller Assemblies instead of ordinary Carbon Brushes which offers more reliability and trouble free performance of the equipment. 

• 2. Double Wound Buck / Boost Type Series Transformer 

• In our Buck/ Boost transformer we are using CRGO lamination to minimize iron losses and coils of Buck / Boost transformer are wound with heavy section of multi strips electrolytic copper to minimize copper losses for getting better efficiency of the equipment. 

• 3. Electronic Control Circuit and Meter Panel.  

• PEC Automatic Voltage Controller consists of very simple electronic control circuit for monitoring and controlling voltage, repair & maintenance of which is very easy.
• The regulator and Buck / Boost transformer are oil cooled, housed in same or separate sheet steel tanks. Radiators are provided for effective cooling. The coils of voltage regulator & Buck / Boost Transformers are vacuum impregnated and oven dried as per IS.
•        
•  TECHNICAL SPECIFICATIONS                                                                                    
• PEC   Servo Stabilizers are available in a wide range and various models. The standard three phase models are suitable for balanced & unbalanced supply and loads. The standard models conform to the following specification:

 

Input Voltage   Efficiency (as per calculation)	360-450  V        99.5%	350-460 V        99.3%	340-460 V       99.10%	340-480 V          99%	320-480 V        98.7%	300-500 V         98.10%
Output Voltage	400 V ± 1%, 3 PHASE, 50 Hz
Output voltage Adjustment	± 5%
Output voltage Regulation	± 1% (at no load / full load)
Correction Rate	10 V – 15 V /SECOND (OR AS Per Requirement)
Temperature Rise (Max)	35 C- above ambient
Cooling	Naturally Oil Cooled.
Insulation	Class A
Type	Indoor.
Mode of system	Fully Automatic / Semi Automatic / Manual
Mounting	On Uni - directional Wheel
Wave form distortion	Nil
Duty Cycle	100% Continuous

 

All specifications / calculations are subjected to change due to regular improvements in products without prior notice.

 

ADVANTAGES  Reduction in Breakdown of Electrical Equipments Improvement in power Factor (only in case of High Voltage) Power Saving (reduction in Power Bills) Depreciation as per Income Tax Act. In India Uniform Quality of end Products Better Efficiency in Plant Reduction in MDI

 

 

 

 

 

• Power Engineers Company is Manufacturer, Exporter & Supplier of a wide range of electrical equipment. The company was established in 1998 and is owned and managed by Mr. Prem. The company has soared to enviable heights in the domain, under his able leadership. Our range of products includes Power Distribution Transformer, Ultra Isolation Transformer, Special Purpose Transformer, Servo Voltage Stabilizers, Variable Voltage Regulator, and Electroplating Rectifiers.
• Vision and Mission :Our Vision is to become a technology based Indian Engineering Company & to emerge out as a leading manufacturer in the domestic & international market."It's our mission to strive for synergy between technology, systems and human resources, to produce products and services that meet the quality, performance and price aspirations of our customers. While doing so, we maintain the highest standards of ethics and social responsibilities."
• Customer Satisfaction :We are the manufacturers and exporters of quality products in the industry. Quality for us is not just a word that defines our product but our capability to achieve complete customer satisfaction. Working with the prime focus of achieving complete customer satisfaction, we work in coordination with our clients to conceptualize their idea and manufacture machines exactly as per their requirements. We also provide our customers excellent after sale service for the maintenance and long service life of the machine. Equipped with the most sophisticated technology and competent engineers, we have innate capability to meet every requirement of our esteemed customers.