Crushing cavity selection
Crusher size | type of cavity | Standard | Short head | ||
min.Settimg | feed opening | min.Settimg | feed opening | ||
HY145(HP200) | Sfine mediust coarse | 14mm 18mm 22mm | 95mm 125mm 185mm | 8mm 10mm 12mm | 20mm 55mm 80mm |
HY220(HP300) | stfine medium coarse | 16mm 20mm 26mm | 110mm 150mm 215mm | 8mm 10mm 12mm | 25mm 60mm 85mm |
HY300(HP400) | stfine medium coarse | 16mm 22mm 25mm | 130mm 170mm 280mm | 8mm 10mm 12mm | 25mm 60mm 90mm |
HY375(HP500) | stfine medium coarse | 16mm 22mm 32mm | 130mm 200mm 300mm | 8mm 10mm 12mm | 25mm 60mm 90mm |
HY450(HP700) | stfine medium coarse | 19mm 25mm 32mm | 210mm 265mm 365mm | 8mm 10mm 13mm | 40mm 90mm 155mm |
Weights,clearance dimensions,power
HY145 | HY220 | HY300 | HY375 | HY450 | ||
kg | crusher complete | 10,500 | 15,500 | 22,000 | 31,000 | 63,000 |
bowl,bowl liner,adj.cap hopper | 2,600 | 3,500 | 5,000 | 7,500 | 17,000 | |
head,mantle and feed plate | 1,000 | 1,850 | 3,500 | 5,000 | 9,000 | |
mm | length(to the end of countershaft)×width×highth | 2000 ×1800 ×1900 | 2300 ×2050 ×2100 | 2800 ×2400 ×2300 | 3100 ×2750 ×2750 | 3900 ×3500 ×4000 |
foundation bolt location | 1090 ×1090 | 1320 ×1320 | 1660 ×1660 | 1764 ×1764 | 2260 ×2260 | |
clearance to remove countershaft box ass | 1870 | 2050 | 2500 | 2700 | 3500 | |
clearance to remove main shaft assembly | 2200 | 2500 | 2900 | 3400 | 3900 | |
power kw | 145 | 220 | 300 | 375 | 450 | |
Open circuit-peak capacity t/h
crusher size | closed side setting and capacity (mm) | |||||||
10 | 12.5 | 16 | 19 | 25 | 32 | 38 | 50 | |
HY145 | 90-120 | 120-150 | 140-180 | 150-190 | 170-220 | 190-235 | 210-250 | -- |
HY220 | 115-140 | 150-185 | 180-220 | 200-240 | 230-280 | 250-320 | 300-380 | -- |
HY300 | 140-175 | 185-230 | 225-280 | 255-320 | 295-370 | 325-405 | 360-450 | 475-580 |
HY375 | 175-220 | 230-290 | 280-350 | 320-400 | 365-455 | 405-505 | 445-555 | 580-725 |
HY450 | 260-325 | 325-410 | 385-480 | 435-545 | 495-620 | 545-680 | 600-750 | 785-980 |
Crusher Capacity Charts:
The capacity charts shown apply to material weghing 100 pounds per cubic foot or 1600 kg per cubic meter. The runge of work index is 14 to 18 kwh. The feed moisture is 4%. The crusher is one component of the circuit. As such, its performance is in part dependent on the proper selection and operation of others equipment. Where used to the following factors will enhance crusher capacity and performance.
1,Proper selection of crushing chamber depended on the feed size, the crushing characteristics of the rock and the requirment to the crushing products. The feed size must be smaller than the closed side feed opening.
2,A feed grading containing proper distribution of the particle sizes.
3,Controlled feed rate.
4,proper feed distribution around the crushing chamber.
5,Adequate crusher dischage area.
6,Discharge conveyer sized to carry maximum crusher capacity.
7,Properly sized scalping and closed circuit screens. The following factors will detract from crusher capacity and performance.
1,Sticky material in crusher feed.
2,Fines in crusher feed (smaller than crusher setting) exceeding 10%.
3,Excessive feed moisture.
4,Feed segregation in crusher cavity.
5,Improper feed distribution around circumference of crushing cavity.
6,Lack of feed control.
7,Extremely hard or tough material.
8,Operation of crusher at less than recommented full load countershaft speed.
APPLICATION:
HP series hydraulic cone crusher is widely used in mining cement, sand stone industry. As secondary and tertiary crusher, it is crushing all kinds of stones, like ore, metallic rock, bauxite, quartz, basalt and limestone.
Features:
- The Sanland HP cone crusher is made with American technology;
- A hydraulic crusher and high productivity;
- Automatic cavity clearing, hydraulic adjustment;
- Grease lubricating system, low consumption and environmentally friendly;
- Less return materials (able to be reduced to 20%);
- Simple structure, convenient in replacement.
- Hydraulic release ,lock, adj and clearage.
