Specifications

Butterfly Valves with Pneumatic Actuator made by italy Lapar valve, Fire Protection Butterfly Valves, A type Butterfly Valve, LT

Butterfly Valves with Pneumatic Actuator , A type Penumatic Actuator Butterfly Valve, LT type Butterfly Valves with Pneumatic Actuator

LPB11/14 butterfly Valve with Pneumatic Actuator has unique shape, compact structure, high-strength disc using frame structure. It has bidirectional sealing function for installation without the interference of the medium flow direction. The surface is coated with epoxy resin, which could prevent rust effectively, a wide choice of seat material can be used in different medium, such as water, oil…

Design Feature

1. Optional multi-pressure stage
2. Special design will not cause death card
3. Torque and lighter, easy to replace the seat
4. Unique shape
5. Frame structure
6. Coated disc

Butterfly Valves with Pneumatic Actuator

Parameter

Actuator	Electric, Pneumatic, Handwheel, Handle
Control	On-off, Modulating, Inteligent
DN	40~1200mm
Pressure	1.0~2.5Mpa
Temperature	EPDM: -29~120°C, FPM: -29~150°C EPT: -20~140°C, CR: -29~80°C NBR: -29~80°C, SI: -29~200°C
Connection	Flange, Wafer
Structure	A Type, LT Type
Body Material	SS316L, SS316, SS304, SS304L, WCB, Casting Iron, Ductile Iron
Disc Material	SS316L, SS316, SS304L, Casting Iron, WCB, B148, Ductile Iron+Nylon 11, CE3MN
Seat Material	NBR, EPDM, EPT, FPM, CR, SI
Medium	Water, Liquid
Option	Limit Switch, Positioner, Solenoid Valve, Pressure-relief Valve

Butterfly Valves with Pneumatic Actuator

Design standard:

Valve body is designed to meet ISO 5752.

 

       Upper flange standard:

              24” and below, valve mounting flange and stem shall be per ISO 5211.

              28” and above, valve mounting flange shall be per ISO5211, stem shall be round keyed.

 

       Flange standard:

              LPB11: ASNI 150 B16.5, JIS B2211, GB 9113.1

              All wafers have locating holes for ease of installation.

 

       Pressure rating:

              Bi-directional bubble-tight shut off to:     16 bar (230PSI) – DN40~DN600mm

                                                                      10 bar (150PSI) – DN650~DN1200mm

              And tested to 110% of full rating:     18 bar (260PSI) – DN40~DN600mm

                                                               11 bar (160PSI) – DN650~DN1200mm

       Shell testing:

              The body strength can stand 150% of full rating: 24 bar (340PSI) – DN40~DN600mm

                                                                                    15 bar (220PSI) – DN650~DN1200mm

 

       Installation instruction:

       The valve is designed for using between all types of flat or raised face flange, do not use flange gaskets. For proper installation, the space between flanges must be sufficient to permit valve insertion without disturbing the rubber liner flange seal. Rotate the stem to position the disc within the body, place the valve between flanges and hand-tighten the bolts. Slowly open the valve counter clockwise to check for adequate disc clearance. Rotate the disc to 10% open position and cross tighten all bolts again check for adequate disc clearance.

Stem retaining mechanism:

       The stem is retained in the body through a special Q type design when the size is under DN350mm, so the stem can be removed from the body and disc without any special tools. Only when being disassembled, the valve disc can be positioned around 135º.

 

       Others:

       According to customer requirements.

  Butterfly Valves with Pneumatic Actuator