Best Cationic Polyelectrolyte Liquid

for Oil Refinery Waste Processing

1. Blufloc Polyacrylamide (PAM) / Polyelectrolyte Emulsion is water in oil solvent type polymer with Anionic and Cationic types.
2. Molecular is high, with a charge density ranging from 0-60% and solid content from 35-40%.
3. It is most often used to increase the viscosity of water (creating a thicker solution) or to encourage flocculation of particles present in water.
4. Due to the polar groups on the molecular chain containing a certain amount, it can through the adsorption of solid particles suspended in water, bridging between particles or through the charge and make the particle formation of large flocs condensation. So, it can accelerate the settlement of particles in suspension, have obvious to speed up the solution to clarify, promote filtering and other effects.
5. Mainly used for various industrial wastewater flocculation sedimentation, sedimentation and clarification treatment, such as iron and steel plant wastewater, electroplating wastewater, wastewater metallurgy, coal washing wastewater treatment, sludge dewatering. Can also be used to clarify and drinking water purification treatment, and sugar & juice mills.
6. Soluble in water, safe, non-toxic, hydrolytic stability, is not sensitive to the change of pH value, anti-chlorine. Harmless, no-flammable and non-explosive, it can be stored at room temperature, it cannot be placed in the sun. It is slightly acidic, when skin contact, wash immediately with plenty of water.

Main Applications:

Oil-displacing Agent of Oil Field Tertiary Oil Recovery:

It can adjust the rheology of filled water, increase the viscosity of driving liquid, improve water drive wave and efficiency, lower water phase permeability in ground layer, and enable water and oil to flow forward at even speed. Its effect is that it is mainly used in tertiary oil recovery of oil fields in the aspect oil production, and raw oil of about 100 to 150ton more can be produced through filling the macromolecule polyacrylamide product one ton.

Well Drilling Mud Raw Materials:

In oil field exploration and development and exploration of geology, water and coal, it is used as adhesive of well drilling mud raw materials, can improve the service life of drill bits, improve the drill speed and drilling footage, and reduce plug in replacing drill, and has prominent well slough preventing effect, and it can be used as fracturing fluid of oil fields or plugging agent of controlling profile and plugging water. 

Flocculant:

The polarity gene adsorbs the solid particles dispersed in water, bridges between the particles and formats the large aggregates, sedimentation and separates of water, flocculates detritus and clay in drilling fluid.

Dispersant:

In the drilling mud treatment, this product can improve the lubricity and stability of the mud to reduce the water loss, prevent sticking effectively, increase drilling efficiency.

Blocking Agent:
The product can generate cross linking under the effect of Al3+, Fe 3+, Ca2+ and other ions, a part of high molecular compound is changed from linear shape into body shapes. The product is not watersoluble, and can be adsorbed on the borehole to block ground layer gaps and topreven the leakage of drilling fluid.

Lubricant:
The product can be absorbed on the surface of metal or clay particles to form liquid film to change friction on the solid surface into liquid frication, thereby lubricating drill bits and drills, lowering the mud cake frication coefficient, and reducing underground accidents.

Fluid Loss Additive:

The hydrolysis degree is higher, the hydration group on the molecular chain is more, the hydration is better, and it changes from flocculant into fluid loss additive. Drilling mud should be treated to keep cake’s permeability as low as possible in order to maintain a stable borehole and to minimize filtrate invasion, and damage to the pay zone.

Shale Inhibition Agent:

The multipoint adsorption of polymer formats to the crisscross membrane macromolecules, plays a role of enhancing the stability of borehole .

Other Application Fields:

NO.

Industry

Application Area

1

Coal Mine

Washing

Coal washing tailing centrifugal separation

Sedimentation and filtration of coal powder and coal mud.

Highly improve the recovery rate of coal powder and the filtration speed.

2

Sewage Water

Treatment

Nonionic-polyacrylamide for acidophilic water systems.

If matched with PAC, aluminum sulphate, the effect will be excellent.

3

Metallurgical 

Mineral Dressing

In floatation and smelting of Zinc, manganese and copper mines, its leachate and slag can be added into PAM to improve the separation efficiency.

4

Textile

Textile Sizing, as a kind of composition for chemical grout, starch textiles

Highly improve the adhesive property, penetrability and desizing performance,

enable the textile to have electrostatic prevention performance, reduces the

desizing rate, and reduces the starch mixing spots, cloth machine breaking

efficiency, and falling objects.

5

Paper-making

Used as fixing agent, residency agent, filtration aid and paper dry and wet

intensity reinforcing agent in paper-making industry.

6

Sand Prevention

Solidification

Dissolved into 0.3% concentration and cross-linking agent added.

It can be sprayed on desert to prevent and solidify sand.

7

Oil field

Oil field profile controlling and water- plugging agent, matched with lignocellulose

and a certain amount of chemical adhesive added.

It can be used as oil field profile controlling and water-plugging agent.

8

Well Drilling

Mud Additives

In oil field, as a kind of mud additives.

To increase the viscosity of water and improve the effectiveness of the water

flooding process.

9

Chemical mudding agent

as chemical mudding agent for plugging water of dikes, ground foundation, channels and the like.

Advantages of Blufloc Polyacrylamide: 

• Economical to use - lower dosage levels.

• Easily soluble in water; dissolves rapidly.

• Non corrosive of suggested dosage, economical and effective at low levels.

• Can eliminate the use of alum & further ferric salts when used as primary coagulants.

• Reduction in sludge of dewatering process system.

• Faster sedimentation, better flocculation.

• Non-pollution (no aluminum, chlorine, heavy metal ions etc.).

• 10 years manufacturing experience, with more than 20 technical engineers

Application and Dosage:

The dosage range of varies from 0.2 - 3.0 ppm depending upon the type of effluent and application. Advised to do jar tests for evaluating the functioning and approximate dosage. 

Jar Test: 

Put sample of effluent in a beaker and add it as designated, agitate for 1 minute at 100-120 rpm and then slowly agitate at 60rpm. Determine the floc properly at this time and note the sedimentation and clarity of top solution. 

Procedure and precautions upon dispersion and dissolving flocculants:
Dissolving time: The time required to dissolve the flocculant varies according to the type of flocculant, water quality, temperature and agitation. However, most flocculants generally require around 1 hour of agitation to completely dissolve the powder. Incomplete mixture of flocculant or lumping may inhibit the performance of the flocculant. 

Agitation speed: The ideal revolution of the agitator is between 200-400rpm. A high speed agitator operating without reducing the revolution of a motor is not advised, since it may cut the molecules of the flocculant. An ideal agitator motor should be of 1HP for a 1-2m3 mixing tank. 

Dissolving concentration: Flocculants should be standardly be dissolved to 0.1-0.5% concentration. It is also effective to start dissolving at a slightly higher concentration, and then dilute the flocculant mixture immediately before use. 

Handling measures and precautions:
Proper human safety products such as Splash goggles, lab coat, vapor respirator, gloves and boots should be worn while handling and applying chemicals. Splashes on skin should be washed off with water immediately. In case of splashing into the eyes, flush it with fresh water and obtain medical attention. Should not be injected. Please refer MSDS for more details. 

Contact us for more information:

1. Call: 0086-510-87821568 or Fax: 0086-510-87821558
2. Email: eric.min(@). or 
3. Skype: eric.bluwat

What's the Functional Principle  of Polyacrylamide?   

• Flocculation Mechanism:

Adsorbing suspension particles, polymer chains entangle and cross-link each other to form bridging, and make flocculation structure enlarge and thicken, and has the functions of surface adsorption and electric neutralization.

• Reinforcing Mechanism:

PAM molecule chain and dispersed phase form bridging bond, ion bond and covalent bond to increase combination strength. 

Package and Storage:

1. 25kg , 200kgs or 1000kgs plasic drums.
2. Stored in original packaging in cool and dry place.
3. Shelf life: 2 years.

FAQ: 

A: 1.We can prive a certain quantity of free sample.

     2. Give us your Fedex account to arrange sample

     3. Place order to Fedex .

A:  Give us your exactly quantity, packing, destination port or specs requirements to quote price.

A: The best way to request sample to test, after confirmation, you can place trial order.

A: No problem, we would like to grow up together.

A: We can provide application methods to you.

A: We discuss about to be an agent after some orders and trust.

A: Yes, we have provided OEM service to lots of big and famous companies in the order.

A: 1000kgs of MOQ.

A: More than 50000tons annual year.

A: 1. Quality is the life of our company, in the past 15 years, quality brings us the benifits and gives us the vitality.

    2. We can ensure the quality consistancy.

    3. If you still don't trust us, you can request the third part company, such as SGS, to inspect and test the bulk cargo before shipment(you should bear the inspection expense).

Company Information: 

• Bluwat Chemicals is a professional supplier of water treatment chemicals and oil field chemicals in China. We provide our customers of both traditional and innovative products to ensure optimum control in a wide variety of applications including the treatment of drinking water, wastewater, process water, and also including oil/gas drilling and oil production.

• Our core products are inorganic coagulants and organic flocculants for the treatment of water and polymer, PHPA/Polyacrylamide for oil/gas drilling and EOR (enhanced oil recovery). We also supply PAC and CMC for drilling application.

• We built our own plants for our products to supply competitive products to our customers in all over the world. Our development work emphasizes working together with our customers to have higher performance and lower dosage on chemicals.

• Our main business is for foreign market, we provide competitive products and efficient operation according to requirements from our customers, we also provide professional application support.

• We are exporting our chemicals to more than 30 countries in the world, including Europe, USA, South and Central America, South-East Asia, Middle East, CIS and etc. We have good cooperation with many chemicals companies and water treatment companies on our products in different market, and we have had good cooperation partners as agent in some important market.