Specifications:
1. Charge Cable length: approx. 1M
2. Transmitter: 3.7V, 500ma Lip
3. Receiver: 3.7V, 500ma Lip
4. Frequency: 433.825MHz
5. Color: Black
Features:
1. 100 levels of vibration.
2. 100 levels of static.
3. The range is about 300m.
4. The levels can be altered by use of up & down button.
5. Collar length is adjustable from 8 to 20 inch.
6. A tone button activates a tone on the collar receiver.
7. The system can be used for 2 receivers.(The additional receiver must be the same type as your previous one and purchased from us)
Power Saving:
1. The Collar Receiver will TURN OFF if it is unused for 4 minutes.
2. Any movement will activate the Collar Receiver into STANDBY MODE.
3. The Transmitter will go into STANDBY MODE if there is no operation after 20 seconds and turn off after 2 minutes.
How to Charge the Remote Transmitter:
1). Connect the charger connector to the charging jack.
2). Plug the charger into a standard outlet.
3). The red light on the Transmitter will be lighted.
4). Charge the Transmitter at least 6 hours for the first charger.
5). After fully charged, the red led will be turned off automatically.
How to Use the Tra nsmitter:
1). To turn on/off the Transmitter,Press the mode button on the Transmitter for 5 seconds.
2). By pressing the Mode button to change to different modes ----the LCD images will change.
3). Press the up and down buttons on right hand side to set level.
4). Choose the different channels for different receivers.
5). The Transmitter will go into STANDBY MODE if not operated for 20 seconds and will TURN OFF if not operated for 2 minutes.
6). In STANDBY MODE, press any button (except LED light button) to wake it up.
How to Charge the Collar Receiver:
1). Connect the charger connector to the charging jack.
2). Plug the charger into a standard outlet.
3). The red LED light inside the Collar Receiver will turn on.
4). Charge the Collar Receiver at least 6 hours for the first charge.
5). After fully charged, the red LED light will be turned off automatically.
6). When charging is completed, put the rubber cover in the right position to keep the internal unit from dust and water.
Low battery Indicator:the Collar Receiver will keep beeping for 2 minuets unless It gets charged.
How to Connect the Transmitter with the Collar Receiver:
1). Turn on the Transmitter and choose 1or 2 channels to encode.
2). Lift the Reset part of the Rubber cover in the Collar Receiver.
3). Use a toothpick or paper click to insert into the Reset HOLE inside the Collar Receiver.
4). Press the LAUNCH button on the Transmitter immediately while you are hearing a beep from the collar.
5). The Collar Receiver will beep , it means that the Transmitter has encoded the collar.
6). After completion, put the rubber cover in the right position to keep the internal unit from dust and water.
Note:
1. The valid distance of remote control means the straight-line distance between the Transmitter and the Collar Receiver without obstacles in between.
2. The life span of the batteries vary to how often you use the product. Therefore you should often check the batteries.
Package includes:
1 x Remote control unit
2 x Collar
2 x Test light & Replacement probes
1 x Charger & Cord
1 x User Instruction
1. Charge Cable length: approx. 1M
2. Transmitter: 3.7V, 500ma Lip
3. Receiver: 3.7V, 500ma Lip
4. Frequency: 433.825MHz
5. Color: Black
Features:
1. 100 levels of vibration.
2. 100 levels of static.
3. The range is about 300m.
4. The levels can be altered by use of up & down button.
5. Collar length is adjustable from 8 to 20 inch.
6. A tone button activates a tone on the collar receiver.
7. The system can be used for 2 receivers.(The additional receiver must be the same type as your previous one and purchased from us)
Power Saving:
1. The Collar Receiver will TURN OFF if it is unused for 4 minutes.
2. Any movement will activate the Collar Receiver into STANDBY MODE.
3. The Transmitter will go into STANDBY MODE if there is no operation after 20 seconds and turn off after 2 minutes.
How to Charge the Remote Transmitter:
1). Connect the charger connector to the charging jack.
2). Plug the charger into a standard outlet.
3). The red light on the Transmitter will be lighted.
4). Charge the Transmitter at least 6 hours for the first charger.
5). After fully charged, the red led will be turned off automatically.
How to Use the Tra nsmitter:
1). To turn on/off the Transmitter,Press the mode button on the Transmitter for 5 seconds.
2). By pressing the Mode button to change to different modes ----the LCD images will change.
3). Press the up and down buttons on right hand side to set level.
4). Choose the different channels for different receivers.
5). The Transmitter will go into STANDBY MODE if not operated for 20 seconds and will TURN OFF if not operated for 2 minutes.
6). In STANDBY MODE, press any button (except LED light button) to wake it up.
How to Charge the Collar Receiver:
1). Connect the charger connector to the charging jack.
2). Plug the charger into a standard outlet.
3). The red LED light inside the Collar Receiver will turn on.
4). Charge the Collar Receiver at least 6 hours for the first charge.
5). After fully charged, the red LED light will be turned off automatically.
6). When charging is completed, put the rubber cover in the right position to keep the internal unit from dust and water.
Low battery Indicator:the Collar Receiver will keep beeping for 2 minuets unless It gets charged.
How to Connect the Transmitter with the Collar Receiver:
1). Turn on the Transmitter and choose 1or 2 channels to encode.
2). Lift the Reset part of the Rubber cover in the Collar Receiver.
3). Use a toothpick or paper click to insert into the Reset HOLE inside the Collar Receiver.
4). Press the LAUNCH button on the Transmitter immediately while you are hearing a beep from the collar.
5). The Collar Receiver will beep , it means that the Transmitter has encoded the collar.
6). After completion, put the rubber cover in the right position to keep the internal unit from dust and water.
Note:
1. The valid distance of remote control means the straight-line distance between the Transmitter and the Collar Receiver without obstacles in between.
2. The life span of the batteries vary to how often you use the product. Therefore you should often check the batteries.
Package includes:
1 x Remote control unit
2 x Collar
2 x Test light & Replacement probes
1 x Charger & Cord
1 x User Instruction
