Product Details

Use 3 “AAA” alkaline batteries phone alcohol tester

Product Pictures of alcohol tester

Technical Data

Sensor type: NM Hot-wire alcohol sensor

tection Range: 0.000~0.199%BAC; 0.00~1.99‰BAC; 0.00~0.99mg/L

Alarming Level: 05%BAC, 0.25mg/L; 0.5‰BAC

Accuracy: ±10% F.S

Response Time: <5s Warm-up Time: <20s

Resume Time: ≤20s

Working Voltage: DC4.5V(3×AAA)Batteries; Working Current: ≤120mA

Working Environment: Temperature -10℃~50℃ Relative Humidity ≤95% No Dews

Display: 3 digitals LCD display with blue backlight
Dimension: 103×65×27mm (L×W×H), ≤64 g Battery excluded
Battery expectancy time: ≥200Times

1. Structure and Function Guide

1.1 Structure Guidepicture:

1	Mouthpiece
2	Buzzer hole
3	Switch Button
4	Input for external power
5	LCD Screen
6	Vent hole

1.2. Function Guide

2. Operation Instruction
2.1. Slide down the battery compartment on the back side, insert 3pcs AAA 1.5V batteries inside according to battery polarity indication and close it.
2.2. Press the power button for 1S, after 1 beep sound, “ warm up “ will be displayed on LCD , after 20 second with 1 “beep“ sound, “ blow” will be displayed on LCD and start to countdown and inform for testing.

2.3. Blow directly to the mouthpiece, after 4 seconds with 1 ”beep” sound to inform to stop blowing and the test result will be displayed on LCD.

2.4. Unit switch: On test result mode, press “power“ button to change the unit (% BAC-‰BAC -mg/l) the final unit will be displayed for next test.

2.5. Auto Power off: tester will auto power off after test result show on LCD for 20 Seconds.

2.6. The LCD flickering indicates low power of batteries, please replace two “AAA” alkaline batteries

2.7. Sensor fault self checking : when turn on , tester will check sensor’s mode is normal or abnormal, if some abnormal thing is found which can auto repair ( about 10 seconds), if can not be repaired, LCD will display “ ER”.
2.8. If a new testing needed, press the switch button again and repeat the above step 4.2~
3. Notification
3.1. Avoid any fall or strong shock.
3.2. If noise gas with high concentration existed, may the tester won’t work normally.
3.3. If testing is done under low voltage, certain error will be existed between the real value.
3.4. To ensure the testing result, please wait 10 min to take the testing after your drinking.
3.5. Please operate it strictly according to this instruction. If long time not use, when you first begin a new testing, the first two times testing result may be unreliable, just begin testing from the third time, otherwise the result will also not be accurate.
3.6. Do not keep the tester in the environment of Corrosive gas (Chlorine etc) for use or deposit, also in other bad surroundings.
3.7. Under normal detections, sensor life could be more than two years.
3.8. After Long time use, there may be dirt on the tester, please use clean cloth to wipe off. Do not use any hard object or the solvent with any Corrosive ingredient.
Remarks: Common Fault and Solving solutions

Fault	Possible reason	Solution
NO display on LCD	Incorrect battery installation	Insert battery correctly according to polarity
	Low battery seriously	New battery replacement
	Circuit fault	Contact distributor
No response to detection gas	not complete Warm-up	Waiting complete Warm-up
No response to detection gas	Circuit fault	Contact distributor
FFF display then power off	Sensor fault	Contact distributor
Low voltage display then power off	Low battery seriously	New battery replacement

To keep the continuous improvement of the products, we reserve the right to improve design without prior notice.

The table of comparison for Alcohol in Blood between the mg/L and BAC

The level of Alcohol display in BAC 0.00%	The level of Alcohol display in mg/L
0.01	0.05
0.02	0.10
0.04	0.20
0.05	0.25
0.06	0.30
0.08	0.40
0.11	0.55
0.12	0.60
0.14	0.70
0.16	0.80
0.18	0.90
0.20	1.00

More Products for You to Choose

About us

With our first factory founded in Shenzhen in 1996, a second was established there in 1998, and a branch office set up in Hong Kong in 2001. Engaged in the manufacturing of various types of solar product,alcohol tester, mobile phone headset and Car MP3/MP4 player. our main series now include solar product,alcohol Tester, mobile phone headset, Car MP3/MP4 player, accessories for iPhone & iPad,Pill Box Timer and DVB-T Product etc.

Why choose

Advantages

♦In order to best meet customers' requirements, a set of comprehensive quality control measures have been integrated into all aspects of the manufacturing process.

♦Featuring consistent quality standards and competitive prices, our products have won popularity in the European, African, Middle Eastern, Australasian, American and Asian markets.

♦To ensure that all series comply with customers' ever-changing demands, our engineers are continually improving existing items and developing new products.

Production line

Certifications

Our Markets

Contact