Product Details

odel	700IIA	700IA
Inside Dimensions	7000(L)X4000(W)X2650(H)mm
Outside Dimensions	7120(L)X5420(W)X3350(H)mm	7120(L)X5670(W)X3350(H)mm
Wall Panels	prepainted steel sheet, double skined with insulation(EPS or Glass-wool), tongue and groove interlock construction, thickness: 60mm.
Doors	3-fold main doors, 2800(W) x2800(H) mm. One personnel door, 800(W)x2000(H)mm
Basement and Floor	Pit base (type 4) or raised metal-base (300mm high) , Floor: 2 rows of gratings and 3 rows of indented plates.
Intake	One backward inclined turbo fan, capacity: 22000cmh, motor: 5.5kW, direct drive	Two double-intake centrifugal fans, capacity: 20000cmh, motor: 4kwx2, belt drive
Extract	One backward inclined turbo fan, capacity: 20000cmh, motor: 7.5kW direct drive	One double-intake centrifugal fan, capacity: 20000cmh, motor: 5.5kw, belt drive
By-pass	Pneumatic damper from spraying to baking cycle
Heating System	Stainless heating exchanger, 60c°-80c° working temperature. Italy Riello one-stage oil burner.(gas burner optional)
Filter System	4 sorts of filters: Prefilter, ceiling filter, floor paint-stop filter, extract paint-stop filter
Ceiling Filtration Area	22m2
Lighting	Upper inclined lights, 10 units, 4X36W each Side wall lights optional
Control System	Reliable components, digital temperature readout, spray and bake temperature settings, bake timer, houer meter, over temperature alarm, indicator lights, emergency stop, “Dwyer” mark II pressure gauge with motorized damper control
Note	Type1: 300mm high raised metal-base with 2pcs ramps outside. Type 2: 300mm high raised metal-base with ramps inside.(Standard) Type 3 : 300mm high raised metal-base, base-down installation, no ramps needed. Type 4: pit style installation, no raised metal-base needed.

Outside Dimensions: 7120(L) ×5420(W) ×3350(H)mm / 7120(L) ×5670(W) ×3350(H)mm

Inside Dimensions: 7000(L)×4000(W) ×2650(H)mm

Entrance Doors: 3000(W) ×2600(H)mm

Personnel Door: 800(W) ×2000(H)mm

Blower capacity: 25,000m³/h

Working temperature: 60^oC -80^oC

Heat Burner: RL 28 oil burner from Riello, Italy.

Filter system: 4 kinds of filters, finely manufactured from “Filtrair” Holland.

BOOTH CABIN

Double skinned walls are solid interlock panel construction, pre-coated finish and prevented with plastic film.

DOORS
Entrance Doors: Insulated, rubber gasket sealed doors with positive internal lock bar in threshold base and solid header base, Standard tri-fold (910 W X 86 H)

Personnel Door: Equipped with safety glass observation window, rubber sealed (211 X 7' )

LIGHTING ASSEMBLY

40 fluorescent lights, horizontal hip light fixtures, Interior or exterior serviceable fixtures are available, extra side lights available (13 sets of horizontal lights or 6 sets of vertical lights optional)

BOOTH FILTRATION SYSTEM

Pre-Filtration: Cleanable pre-filters reduce contamination of ceiling filters.

Ceiling Filters: European style blanket filters provides maximum air movement to evenly envelop the vehicle, and removes all overspray. Filters are held in position by steel knife-edge closures, no foam or rubber sealing.

Paint Stop Filters: Five rows of (5 X26mm W X 23mm L )dry filter

GRATING: Fully galvanized grates and support structure

HEATED AIR RECIRCULATING SYSTEM

a) Indirect-fire 1.0 -1.25 million BTU burner

b) Indirect stainless steel heat exchanger

c) Standard 2 x 5Hp 1750 rpm motors belt drives dual centrifugal fans assembly (2 fans and 2 x 5 Hp motors)

d) Straight intake and exhaust duct for 15 ceiling

e) Fuel - Natural Gas or Propane (please specify when ordering)

EXHAUST SYSTEM

Standard 10Hp 1750 rpm motor belt drive single centrifugal fan

SPRAY CYCLE

100% outside air is drawn through pre-filters, heated to preset temperature, passed through ceiling filters into cabin.

BAKE CYCLE

Fully automatic, including purge and cool-down cycle. Air intake fan draws 10% fresh air into cabin to reduce solvent concentration during bake cycle. Lights turn off automatically during bake mode.

ELECTRICAL AUTOMATIC CONTROL PANEL

Digital temperature controller, hour meter, bake timer, cycle selector, buzzer and indicator lights. All components are recognized, listed or certified by UL, ETL or CE