Function

The device is designed for AC LED Tube,bulb, 220V, 110V energy-saving lights aging product testing, through the LED energy saving lamp 220V high-voltage, medium voltage, pressure, low pressure, high temperature, roaming, the impact of aging, such as voltage area, LED lamps can be observed the above paragraph aging test voltage of this product is approved by the State Patent Office (Patent No.: ZL 2012 2 0526602.7)

The chain plates can age the bulb and LED energy-saving lamp ,  can fully meet the time requirements

.

Full line have 106 chain plates, each plate mounted chain E27 lamp holder 16 five magazines, T8 fluorescent seat four pairs, the aging bulb or fluorescent tube 1696 424 (full line filled).

Crafts

Technology

Points

Temperature zone: the thermostat system is completed by electric heating , set the under layer five meters of the heating section, a second meter installed two 1KW ceramic heating tube, three-point temperature acquisition, automatic temperature control are: room temperature +80 ℃.

Shock beat detection circuit: The day genuine regulator regulator 1 set 10KW 0-250V adjustable, total are six areas, each areas’s impact time can be set on the touch screen interface.

.

Detection normal circuit: The days of genuine regulator regulator 1 set 10KW 0-250V adjustable, set the normal-pressure test area.

Low-voltage detection circuit: The day genuine regulator regulator 1 set 10KW 0-250V adjustable, set the low-pressure test area.

High voltage detection circuit: The day genuine regulator regulator 1 set 10KW 0-300V adjustable, set the high-pressure test area.

Bulb chain plates using E27 screw base.

Tube aging adopted quickly T8 lamps mounted seat fixture. (Lamp holder fixture can mobilize points 300,600,900,1200 MM);

Exterior protection requirements

Fuselage frame is 40 * 40 * 1.5 (MM) made of welded steel pipes, body up and down using 130 * 23 (MM) aging line of special aluminum alloy, retaining plate with 1.5MM cold bending from;

Double pitch transmission chain using a single ear holes inch chain;

Setting stop light passports on the line body, tinted plexiglass and aluminum profiles using a combination of effective energy-saving lamps reduce glare and better protect the eyes.

Exterior Dimensions protection requirements

With two-way full range of electric groove track, using insulating epoxy board. And assembly 3MM thick copper busbars. Assembling a body guard against falls under the net cord to prevent the product to fall break, made of stainless steel mesh on both sides of the pore universal angle iron fixed.

Equipment can not rust,dust.

The noise produced by machine is under 65dB.

Stand with adjustable height adjust able horizontal foot galvanized Cup.

Line body length: 10 m, workbench to the ground height 750 ± 20mm,can adjustable

Dimensions: L10000mm * W1620mm * 1270mm (see 10 meters LED aging line shape engineering schematics).

Power and Transmission

Taiwan bending Wanxin 1.5KW motor with three-phase motors, 1:200 reducer, 2HP inverter, inverter variable speed, line speed 0-2M/min adjustable, adjustable aging time of 0-4 hours.

Using a double φ50inch T17gear shaft and sprocket with a tensioning mechanism for the transmission distance.

Frame

Structure

Fuselage frame: The frame is 40 × 40 × 1.5mm square steel tubes welded; fuselage with 130 × 23 × 2mm aluminum profiles aging line dedicated.

Nose, tail guard uses made of 1.5mm cold plate bending. Lower shading plate with 1.5mm cold plate bending system with 3mm thick tinted plexiglass viewing window, one meter section, each with two buckles hand.

Transport chain: the chain adopt Hangzhou plant produced the single C212A double pitch ear holes of high-strength chain. 30 * 30 GB angle do support rail, up,down a total 2 layers.

Chain plate: 2.0mm cold plate bending rolls into 148 × 1390 × 57mm, each strand board installed a unipolar open space, 16 E27 five clip holder, 4 adjustable seat position T8 fluorescent lamps. Bottom-mounted Road conductive brush (brass). Chain plate black spray.

Online decent set block light shield, using a combination of 3mm tinted plexiglass plate made of aluminum with 40 * 40. Effective energy-saving lamps light attenuation and better eye protection

Conductor rail: across the board with two of the conductor rail, using 5mm epoxy insulation board and chassis. Assembly 3mm × 30 stainless steel aging special conductive tracks

.

Fence: online body assembled a network drop resistance protection to prevent smash off lights, using high-quality stainless steel fine-mesh net production, Specification 8000 × 1400mm, angle iron on both sides with a universal fixed

.